manualshive.com logo in svg

Renault Laguna III, Manual

Share
Download
Renault Laguna III Manual Download Page 3401

47A

-

12

SIDE OPENING ELEMENTS

Rear side door: Stripping - rebuilding

47A

STRIPPING

STRIPPING OPERATION FOR PART CONCERNED

a

Disconnect the supply connector from the rear side
door wiring harness.

a

Remove:

- the rear side door trim (see 

Rear side door trim:

Removal - Refitting

) (MR 416, 72A, Side opening

elements trim),

- the rear side door sealing film (see 

Door  sealing

film:  Removal  -  Refitting

)  (MR  416,  65A,  Door

sealing),

- the  rear  side  door  frame  interior  trim  (see 

Rear

side door frame interior trim: Removal - Refit-
ting

) (MR 416, 72A, Side opening elements trim),

- the anti-fouling seal,

- the  rear  side  door  glass  run  channel  (see 

Rear

side door window run channel: Removal - Refit-
ting

) (MR 416, 66A, Window sealing),

- the rear side door pillar exterior trim (see 

Rear side

door  pillar  exterior  trim:  Removal  -  Refitting

)

(MR 416, 56A, Exterior equipment),

- the  window  winder  motor  (see 

Electric  window

motor: Removal - Refitting

) (MR 415, 87D, Elec-

tric windows - Sunroof) (depending on equipment
level),

- the rear side door sliding window (see 

Rear side

door sliding window: Removal - Refitting

) (MR

416, 54A, Windows),

- the  rear  side  door  fixed  window  (see 

Rear  side

door  fixed  window:  Removal  -  Refitting

)  (MR

416, 54A, Windows),

- the rear side door window winder mechanism (see

Rear side door manual window winder mecha-
nism:  Removal  -  Refitting

)  or  (see 

Rear  side

door  electric  window  mechanism:  Removal  -
Refitting

)  (MR  416,  51A,  Side  opening  element

mechanisms),

- the exterior door handle (see 

Exterior door han-

dle:  Removal  -  Refitting

)  (MR  416,  51A,  Side

opening element mechanisms),

- the rear side door lock (see 

Rear side door lock:

Removal - Refitting

) (MR 416, 51A, Side opening

element mechanisms),

- the rear side door check strap (see 

Rear side door

check strap: Removal - Refitting

) (MR 416, 51A,

Side opening element mechanisms),

- the rear side door moulding (see 

Rear side door

protective strip: Removal - Refitting

) (MR 416,

55A, Exterior protection),

- the rear speakers (see 

Rear speakers: Removal -

Refitting

) (MR 415, 86A, Radio),

- the rear side door wiring.

REBUILDING

I - REBUILDING PREPARATION OPERATION

a

Always replace:

- the sealing film,

- the foam pads.

a

Order a door fitting kit in addition.

II - REBUILDING OPERATION FOR PART 
CONCERNED

a

Refit:

- the rear side door wiring,

- the rear speakers (see 

Rear speakers: Removal -

Refitting

) (MR 415, 86A, Radio),

- the rear side door moulding (see 

Rear side door

protective strip: Removal - Refitting

) (MR 416,

55A, Exterior protection),

- the rear side door check strap (see 

Rear side door

check strap: Removal - Refitting

) (MR 416, 51A,

Side opening element mechanisms),

- the rear side door lock (see 

Rear side door lock:

Removal - Refitting

) (MR 416, 51A, Side opening

element mechanisms),

- the exterior door handle (see 

Exterior door han-

dle:  Removal  -  Refitting

)  (MR  416,  51A,  Side

opening element mechanisms),

- the rear side door window winder mechanism (see

Rear side door manual window winder mecha-
nism:  Removal  -  Refitting

)  or  (see 

Rear  side

door  electric  window  mechanism:  Removal  -
Refitting

)  (MR  416,  51A,  Side  opening  element

mechanisms),

Note:

The  order  of  the  operations  described  below
applies specifically to replacing the rear side door.

The  following  procedure  applies  to  the  rear  side
door on the vehicle.

Summary of Contents for Laguna III




















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands