Renault Laguna III, Manual

Page: 1924 / 3699

23A
-
6
AUTOMATIC GEARBOX
Automatic gearbox: Removal - Refitting
M9R, and AJ0
23A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting ) (MR 415, 02A, Lifting equip-
ment).
a
Remove:
- the engine cover,
- the battery (see Battery: Removal - Refitting )
(MR 415, 80A, Battery),
- the battery tray (see Battery tray: Removal - Re-
fitting ) (MR 415, 80A, Battery),
- the injection computer (see Diesel injection com-
puter: Removal - Refitting ) (MR 415, 13B, Diesel
injection) or (see Petrol injection computer: Re-
moval - Refitting ) (MR 415, 17B, Petrol injection),
- the air filter box (see Air filter unit: Removal - Re-
fitting ) (MR 415, 12A, Fuel mixture),
- the engine undertray bolts,
- the engine undertray,
- the front wheels (see Wheel: Removal - Refitting )
(MR 415, 35A, Wheels and tyres),
- the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting ) (MR 416, 55A, Exterior
protection),
- the front right-hand driveshaft (see 29A , Drive-
shafts , Front right-hand driveshaft: Removal -
Refitting , page 29A-7 ) ,
- the front left-hand driveshaft (see 29A , Drive-
shafts , Front left-hand driveshaft: Removal -
Refitting , page 29A-1 ) ,
- the front bumper (see Front bumper: Removal -
Refitting ) (MR 416, 55A, Exterior protection),
- the headlights (see Headlight: Removal - Refit-
ting ) (MR 415, 80B, Headlights),
- the front end panel (see Front end panel: Remov-
al - Refitting ) (MR 416, 42A, Front upper struc-
ture),
- the particle filter (see Particle filter: Removal -
Refitting ) (MR 415, 19B, Exhaust).
a
Drain:
- the cooling system (see Cooling system: Drain-
ing - Refilling ) (MR 415, 19A, Cooling),
- the automatic gearbox (see 23A , Automatic gear-
box , Automatic gearbox oil: Draining - Filling ,
page 23A-29 ) ,
- the refrigerant circuit (see Refrigerant circuit:
Draining - Filling ) (MR 415, 62A, Air conditioning).
a
Remove:
- the radiator mounting cross member (see Radiator
mounting cross member: Removal - Refitting )
(MR 416, 41A, Front lower structure),
- the rear suspended engine mounting (see Lower
engine tie-bar: Removal - Refitting ) (MR 415,
19D, Engine mounting),
- the right-hand suspended engine mounting (see
Right-hand suspended engine mounting: Re-
moval - Refitting
) (MR 415, 19D, Engine mount-
ing),
- the left-hand suspended engine mounting (see
Left-hand suspended engine mounting: Re-
moval - Refitting
) (MR 415, 19D, Engine mount-
ing),
- the engine - gearbox assembly (see Engine -
gearbox assembly: Removal - Refitting ) (MR
415, 10A, Engine and peripherals).
Special tooling required
Mot. 1390 Support for removal - refitting
of engine - gearbox assembly
Equipment required
workshop hoist
Diagnostic tool
Tightening torques
m
gearbox bell housing
nuts and bolts 44 Nm
converter nuts 44 Nm
starter bolts 44 Nm
starter ear th cable bolt 21 Nm
nut on the positive ter-
minal of the starter 8 Nm
nut on the excitation ter-
minal of the starter 5 Nm