manualshive.com logo in svg

Renault Laguna III, Manual

Share
Download
Renault Laguna III Manual Download Page 186

10A

-

109

ENGINE AND CYLINDER BLOCK ASSEMBLY

Engine oil: Draining - Refilling

K4M

10A

PARTS AND CONSUMABLES FOR THE 
REPAIR WORK

a

parts always to be replaced: Drain plug seal on
engine oil sump (10,03,01,04)

I - OIL SERVICE

a

Position the vehicle on a two-post lift (see 

Vehicle:

Towing and lifting

) (02A, Lifting equipment).

a

Remove:

- the engine cover,

- the filler cap (

1

) ,

- the dipstick (

2

) ,

- the engine undertray.

Equipment required

oil recovery tray

oil change wrench

oil change end piece with an 8 mm square drive

Tightening torques

m

drain plug

20 N.m

Engine

Average oil capacity

(adjusting using dipstick) (l)

Oil  change  with-
o u t  

fi l t e r

replacement

Oil  change  with
filter  replace-
ment

K4M

4.9

5

IMPORTANT

Wear  leaktight  gloves  (Nitrile  type)  for  this  opera-
tion.

128255

Summary of Contents for Laguna III




















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands