Renault Laguna III Manual Download Page 660

Page: 660 / 3699

11A

282

TOP AND FRONT OF ENGINE

Camshaft dephaser solenoid valve: Removal - Refitting

M4R

11A

REMOVAL

I - REMOVAL PREPARATION OPERATION

Position the vehicle on a two-post lift (see

Vehicle:

Towing and lifting

) (MR 415, 02A, Lifting equip-

ment).

Remove:

- the engine cover,

- the engine undertray bolts,

- the engine undertray.

Remove:

- the engine tie-bar bolts (

) ,

- the engine tie-bar (

) ,

- the right-hand suspended engine mounting (see

19D

Engine mounting

Right-hand suspended

engine mounting: Removal - Refitting

, page

19D-51

) .

II - OPERATION FOR REMOVAL OF PART
CONCERNED

Disconnect the connector (

) of the camshaft

dephaser solenoid valve equipped with a new seal.

Remove:

- the bolt (

) from the camshaft dephaser solenoid

valve,

- the camshaft dephaser solenoid valve,

- the camshaft dephaser solenoid valve seal.

REFITTING

I - REFITTING PREPARATION OPERATION

Always replace the camshaft dephaser solenoid
valve seal.

II - REFITTING OPERATION FOR PART
CONCERNED

Refit:

- the camshaft dephaser solenoid valve equipped

with a new seal,

- the camshaft dephaser solenoid valve bolt.

Torque tighten the

camshaft dephaser solenoid

valve bolt (10 N.m)

Tightening torques

camshaft dephaser
solenoid valve bolt

10 N.m

engine tie-bar bolts

190 N.m

123347

115496

Summary of Contents for Laguna III




















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Laguna III

Reviews:

Brands by name

Popular brands

Renault Laguna III, Manual

Search results

Summary of Contents for Laguna III

Reviews:

Brands by name

Popular brands