![background image](http://html1.mh-extra.com/html/omron/r6yxg500/r6yxg500_installation-manual_742792028.webp)
Safety Instr
uctions
S-18
3.
Use caution when releasing the Z-axis (vertical axis) brake
WARNING
THE vERTICAL AXIS WILL SLIdE doWnWARd WHEn THE bRAKE IS RELEASEd, CAUSInG A HAZARdoUS
SITUATIon. TAKE AdEqUATE SAFETY mEASURES In ConSIdERATIon bY TAKInG THE WEIGHT And SHApE InTo
ACCOUNT.
• bEFoRE RELEASInG THE bRAKE AFTER pRESSInG THE EmERGEnCY STop bUTTon, pLACE A SUppoRT UndER
THE vERTICAL AXIS So THAT IT WILL noT SLIdE doWn.
• bE CAREFUL noT To LET YoUR bodY GET CAUGHT bETWEEn THE vERTICAL AXIS And THE InSTALLATIon
bASE WHEn pERFoRmInG TASKS (dIRECT TEACHInG, ETC.) WITH THE bRAKE RELEASEd.
4.
Be careful of Z-axis movement when the controller is turned off or emergency stop is triggered
(air-driven Z-axis)
WARNING
THE Z-AXIS STARTS movInG UpWARd WHEn poWER To THE ConTRoLLER oR pLC IS TURnEd oFF, THE pRoGRAm
IS RESET, EmERGEnCY STop IS TRIGGEREd, oR AIR IS SUppLIEd To THE SoLEnoId vALvE FoR THE Z-AXIS AIR
CYLIndER.
• do noT LET HAndS oR FInGERS GET CAUGHT And SqUEEZEd bY RoboT pARTS movInG ALonG THE Z-AXIS.
• KEEp THE USUAL RoboT poSITIon In mInd So AS To pREvEnT THE Z-AXIS FRom HAnGInG Up oR bIndInG on
obSTACLES dURInG RAISInG oF THE Z-AXIS EXCEpT In CASE oF EmERGEnCY STop.
5.
Take protective measures when the Z-axis interferes with peripheral equipment (air-driven Z-axis)
WARNING
WHEn THE Z-AXIS ComES To A STop dUE To obSTRUCTIon FRom pERIpHERAL EqUIpmEnT, THE Z-AXIS mAY
movE SUddEnLY AFTER THE obSTRUCTIon IS REmovEd, CAUSInG InJURY SUCH AS pInCHEd oR CRUSHEd
HANDS.
• TURn oFF THE ConTRoLLER And REdUCE THE AIR pRESSURE bEFoRE ATTEmpTInG To REmovE THE
OBSTRUCTION.
• bEFoRE REdUCInG THE AIR pRESSURE, pLACE A SUppoRT UndER THE Z-AXIS bECAUSE THE Z-AXIS WILL dRop
UndER ITS oWn WEIGHT.
6.
Be careful of Z-axis movement when air supply is stopped (air-driven Z-axis)
WARNING
THE Z-AXIS WILL SLIdE doWnWARd WHEn THE AIR pRESSURE To THE Z-AXIS AIR CYLIndER SoLEnoId vALvE IS
REdUCEd, CREATInG A HAZARdoUS SITUATIon.
TURn oFF THE ConTRoLLER And pLACE A SUppoRT UndER THE Z-AXIS bEFoRE CUTTInG oFF THE AIR SUppLY.
7.
Make correct parameter settings
CAUTION
The robot must be operated with the correct tolerable moment of inertia and acceleration coefficients that match the manipulator tip
mass and moment of inertia. Failure to follow this instruction will lead to a premature end to the drive unit service life, damage to robot
parts, or cause residual vibration during positioning.
8.
If the X-axis, Y-axis or R-axis rotation angle is small
CAUTION
If the X-axis, Y-axis or R-axis rotation angle is set smaller than 5 degrees, then it will always move within the same position. This
restricted position makes it difficult for an oil film to form on the joint support bearing, and so may possibly damage the bearing. In this
type of operation, add a range of motion so that the joint moves through 90 degrees or more, about 5 times a day.
Summary of Contents for R6YXG500
