manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

CAUTION

unit.
Use a soft cloth or other suitable material to protect the swinging arm and rear suspension unit while the
swinging arm is being removed.

Remove the swinging arm from the motorcycle, carefully passing the rear suspension unit through the
opening in the swinging arm as you do so.

7. 

Check the swinging arm bearings for damage, pitting, and cracks. Replace as necessary.

1. 

Inspect the swinging arm pivots for damage and deformation. Replace as necessary.

2.

Check the swinging arm for damage. Replace as necessary.

3.

Check all bearing seals for damage, splits etc. Replace as necessary.

4.

Check the swinging arm gaiters for splits and other damage. Replace as necessary.

5.

Swinging Arm - Assembly

Pivot Bearings

Remove the seal and inner bearing assembly for the pivot bearings on both sides of the swinging arm.

1.

1

chnz

Seal and inner race assembly

1.

Note

When removing the bearing outer race, the cap will separate from the outer race.

Fit the bearing puller such that the lugs of the tool are between the bearing outer race and its cap.

2.

Assemble the T3880627 - Bearing Puller, 32-42 mm to T3880208 - Slide Hammer, fully engaging the
threads. Draw back the slide part of the hammer swiftly to facilitate the removal of the bearing outer race.

3. 

1

2

4

5

Tiger Explorer XR Series

424 of 746

REAR SUSPENSION

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Parkside PSHL 2 B1 Operation And Safety Notes Translation Of The Original Instructions preview
PSHL 2 B1
Бренд: Parkside Страницы: 89
Parkside PSH 3 A1 Assembly, Operating And Safety Instructions preview
PSH 3 A1
Бренд: Parkside Страницы: 28
Yukon Trail Puma 200 Owner'S Manual preview
Puma 200
Бренд: Yukon Trail Страницы: 21
W-Tec Ondrejnik User Manual preview
Ondrejnik
Бренд: W-Tec Страницы: 6
Contracor COMFORT 10130810 Instructions Manual preview
COMFORT 10130810
Бренд: Contracor Страницы: 36
Metra Electronics Saddle Tramp BC-BTHBSP Installation Instructions Manual preview
Saddle Tramp BC-BTHBSP
Бренд: Metra Electronics Страницы: 8
Happy Trails KTM950 Quick Start Manual preview
KTM950
Бренд: Happy Trails Страницы: 4
Gentex CVC M9 Operation And Maintenance Manual preview
CVC M9
Бренд: Gentex Страницы: 15
Free Spirits 308927 Instructions Manual preview
308927
Бренд: Free Spirits Страницы: 28
hepco & becker 6504518 01 01 Manual preview
6504518 01 01
Бренд: hepco & becker Страницы: 5
Fantic XX 125 Use And Maintenance Manual preview
XX 125
Бренд: Fantic Страницы: 153
PMI Ventilator Instructions preview
Ventilator
Бренд: PMI Страницы: 2
DYNATEK D2K-HD2E User Instructions preview
D2K-HD2E
Бренд: DYNATEK Страницы: 8
DYNATEK D3K7-6 Installation Instructions preview
D3K7-6
Бренд: DYNATEK Страницы: 4
Victory 2009 VISION Rider'S Manual preview
2009 VISION
Бренд: Victory Страницы: 323
Shark S 700 User Manual preview
S 700
Бренд: Shark Страницы: 56
IL Motorsport NC0-0965 Installation Instruction preview
NC0-0965
Бренд: IL Motorsport Страницы: 2
APRILIA ETX 125 Manual preview
ETX 125
Бренд: APRILIA Страницы: 80

Бренды по названию

Популярные бренды

Загрузить еще бренды