manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

achieved after first removing the output shaft first gear and its bearing. The output shaft is an integral part of the
front bevel box assembly and cannot be removed.
The front bevel box assembly contains no user serviceable parts, and must be replaced if any wear or damage
are found. It is permitted however to replace the damper shaft oil seal and the bevel box casing O-rings and
gaskets.
The gear selector shaft can be removed and installed without removal of the transmission, after first removing
the selector cover and gear position sensor.

Gear Change Linkage - Removal

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

Remove the three fixings and remove the expansion tank cover. Discard the upper M5 fixing. Retain the
lower M6 fixings for reuse.

1. 

2

chgw_2

1

3

Expansion tank cover

1.

Upper fixings (M5)

2.

Lower fixings (M6)

3.

Note

The upper ball joint and lock nut on the gear change linkage has a left hand thread. This is identified
by a machined ring on the linkage and on the ball joint.

Loosen the two lock nuts on the gear change linkage.

2.

Note

Note the position of the transmission linkage in relation to the punch mark on the gear change
mechanism.

Select neutral, remove the pinch bolt and disconnect the transmission linkage from the gear change
mechanism.

3. 

1

3

Tiger Explorer XR Series

169 of 746

TRANSMISSION 

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

ZARD ZUMA Fitting Manual preview
ZUMA
Бренд: ZARD Страницы: 2
BMW C 400 X Rider'S Manual preview
C 400 X
Бренд: BMW Страницы: 245
FDC FDC-03B User Manual preview
FDC-03B
Бренд: FDC Страницы: 6
Takegawa 09-12-1010 Instruction Manual preview
09-12-1010
Бренд: Takegawa Страницы: 2
TRS One 250 2016 User Manual preview
One 250 2016
Бренд: TRS Страницы: 38
rizoma BS232 User Manual preview
BS232
Бренд: rizoma Страницы: 16
yasuni TUB807-D57 Assembly Instructions Manual preview
TUB807-D57
Бренд: yasuni Страницы: 9
Bosch GHJ 10,8+18V Unisex Original Instructions Manual preview
GHJ 10,8+18V Unisex
Бренд: Bosch Страницы: 14
Bosch LTE65 Manual preview
LTE65
Бренд: Bosch Страницы: 28
Bosch 06188000DY Original Instructions Manual preview
06188000DY
Бренд: Bosch Страницы: 145
R&G RSET02BK Fitting Instructions Manual preview
RSET02BK
Бренд: R&G Страницы: 17
R&G LP0347 Fitting Instructions Manual preview
LP0347
Бренд: R&G Страницы: 18
R&G LP0253BK Fitting Instructions Manual preview
LP0253BK
Бренд: R&G Страницы: 17
Vance and hines Competition Series Quick Start Manual preview
Competition Series
Бренд: Vance and hines Страницы: 2
Vance and hines 48425 Installation Instructions preview
48425
Бренд: Vance and hines Страницы: 5
Vance and hines 48241 Installation Instructions preview
48241
Бренд: Vance and hines Страницы: 4
Sealey VS779.V3 Instructions preview
VS779.V3
Бренд: Sealey Страницы: 2
HYOSUNG Prima Service Manual preview
Prima
Бренд: HYOSUNG Страницы: 144

Бренды по названию

Популярные бренды

Загрузить еще бренды