manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Carefully feed the electrical connector and harness upwards and out from beneath the front edge of the
battery tray. Press the wire locking device fully in and disconnect the electrical connector.

2. 

Release the fixing securing the purge control valve to the frame.

3. 

Note

Note the position of the purge control valve hoses for installation.

Disconnect the hoses and remove the purge control valve from the motorcycle.

4.

cjkb

4

1

2

3

Purge control valve

1.

Fixing

2.

Hose to throttle bodies

3.

Hose to evaporative canister

4.

Purge Control Valve - Installation

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

Reconnect the purge control valve electrical connector. Route the connector and main harness and position
to the crankcase tidy as noted during removal.

1. 

Reconnect the hoses to the purge control valve as noted during removal.

2.

Fit the purge control valve to the frame and tighten the fixing to 

3 Nm

.

3.

Apply a smear of proprietary general purpose grease to NLGI 2 standard to the ball stud and reconnect the
swinging arm position sensor linkage to the swinging arm.
Reconnect the battery positive, (red) lead first and tighten the terminals to 

4.5 Nm

.

Refit the rider’s seat (see Rider’s Seat - Installation).
Calibrate the rear suspension unit preload motor (see Rear Suspension Unit Preload Motor Calibration).
Calibrate the swinging arm position sensor (see Swinging Arm Position Sensor - Calibration).

Evaporative Emissions Control System

Evaporative Emissions Control System - Engine Off

All Explorer models are fitted with a system to control the evaporation of fuel vapour to the atmosphere.
A carbon filled evaporative canister absorbs vapour while the engine is not running. When the engine is started,
the vapour is returned to the engine and burnt.

Tiger Explorer XR Series

347 of 746

FUEL SYSTEM / ENGINE MANAGEMENT

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Cannondale MX400 Parts Catalog preview
MX400
Бренд: Cannondale Страницы: 61
National Cycle Spartan N21202 Installation Instructions preview
Spartan N21202
Бренд: National Cycle Страницы: 3
Honda 1989 CBR1000F Owner'S Manual preview
1989 CBR1000F
Бренд: Honda Страницы: 104
R&G ECC0310R Fitting Instructions Manual preview
ECC0310R
Бренд: R&G Страницы: 8
Abus GameChanger Instruction Manual preview
GameChanger
Бренд: Abus Страницы: 18
GAS GAS EX 250 2023 Owner'S Manual preview
EX 250 2023
Бренд: GAS GAS Страницы: 144
MSF Sixteenth Edition Operator'S Manual preview
Sixteenth Edition
Бренд: MSF Страницы: 60
SCHUBERTH F300 Manual preview
F300
Бренд: SCHUBERTH Страницы: 43
MSW MSW-MC25L1 User Manual preview
MSW-MC25L1
Бренд: MSW Страницы: 11
BOS Suspension Factory Series Service Manual preview
Factory Series
Бренд: BOS Suspension Страницы: 32
Power Fist 8808560 Instructions preview
8808560
Бренд: Power Fist Страницы: 2
Power Fist 8674285 User Manual preview
8674285
Бренд: Power Fist Страницы: 16
RIEJU Marathon 450 Owner'S Manual preview
Marathon 450
Бренд: RIEJU Страницы: 148
RIEJU MRT 50 Owner'S Manual preview
MRT 50
Бренд: RIEJU Страницы: 162
APRILIA MANA GT ABS - 2009 Owner'S Manual preview
MANA GT ABS - 2009
Бренд: APRILIA Страницы: 189
Honda CG125 Fan Owner'S Manual preview
CG125 Fan
Бренд: Honda Страницы: 146
KTM 79001996000 Information preview
79001996000
Бренд: KTM Страницы: 12
KTM 78012016000 Information preview
78012016000
Бренд: KTM Страницы: 7

Бренды по названию

Популярные бренды

Загрузить еще бренды