manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Note

be repeated.

Slowly depress the brake pedal and, holding the pedal fully down, close the bleed nipple.

6. 

Repeat steps 5 and 6 for the duration of bleed stages 1 and 2.

7.

Note

Maintain the brake fluid level between the upper and lower reservoir levels whilst bleeding is being
carried out.

Once the bleed sequence has completed the diagnostic tool will display a message 

'ABS system bleed

complete'

. Note that this message may take a few seconds to appear after the ABS modulator has become

silent.

8. 

Apply pressure to the brake lever and close the bleed nipple. Tighten the nipple to 

6 Nm

.

9.

Final Steps

WARNING

Use only DOT 4 specification brake fluid as listed in the General Information section of this manual. The use
of brake fluids other than those DOT 4 fluids listed in the General Information section may reduce the
efficiency of the braking system leading to loss of motorcycle control and an accident.
Observe the brake fluid handling warnings given earlier in this section of the manual.

WARNING

It is dangerous to operate the motorcycle with defective brakes; you must have your authorised Triumph
dealer take remedial action before you attempt to ride the motorcycle again. Failure to take remedial action
may reduce braking efficiency leading to loss of motorcycle control and an accident.

CAUTION

To prevent paint damage, do not spill brake fluid onto any area of the bodywork. Spilled brake fluid will
damage paintwork.

Ensure both manual and ABS system bleed procedures have been completed and repeated in the sequence
described at the beginning of the Core Activity section.
In the Triumph diagnostic software, navigate to ENGINE DIAGNOSTICS - FUNCTION TEST and perform
the cruise control switch check (see Cruise Control Switch Check) to ensure correct brake switch operation.
Disconnect the Triumph diagnostic tool.
Fill the reservoir to the maximum level with new DOT 4 fluid.
Fit the reservoir cover and diaphragm. Check for correct diaphragm fitment before final tightening of the
cover.
Remove the bleed tube from the nipple.
Replace the bleed nipple cap.
Refit the heel guard and tighten its fixings to 

7 Nm

.

Check for correct brake operation. Rectify as necessary.

Rear Brake Pads - Removal

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

Tiger Explorer XR Series

482 of 746

BRAKES

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Cannondale MX400 Parts Catalog preview
MX400
Бренд: Cannondale Страницы: 61
oset 12.5 Eco Owner'S Manual preview
12.5 Eco
Бренд: oset Страницы: 20
hepco & becker Easyrack 6617501 01 01 Manual preview
Easyrack 6617501 01 01
Бренд: hepco & becker Страницы: 4
DAELIM Daystar 250 Owner'S Manual preview
Daystar 250
Бренд: DAELIM Страницы: 93
KTM 640 LC4 ENDURO 2006 Owner'S Manual preview
640 LC4 ENDURO 2006
Бренд: KTM Страницы: 60
CYCLOPS KTM 1190 LED Light Bar Instructions preview
KTM 1190 LED Light Bar
Бренд: CYCLOPS Страницы: 4
Yamaha XT250L1 2020 Owner'S Manual preview
XT250L1 2020
Бренд: Yamaha Страницы: 100
Yamaha XT225R Owner'S Manual preview
XT225R
Бренд: Yamaha Страницы: 108
Yamaha MTM690 2022 Owner'S Manual preview
MTM690 2022
Бренд: Yamaha Страницы: 98
Yamaha XSR700 2018 Supplement Service Manual preview
XSR700 2018
Бренд: Yamaha Страницы: 96
Yamaha XJR1300X Owner'S Manual preview
XJR1300X
Бренд: Yamaha Страницы: 94
Yamaha XJ6 2008 Owner'S Manual preview
XJ6 2008
Бренд: Yamaha Страницы: 100
Yamaha WR250R 2007 Owner'S Manual preview
WR250R 2007
Бренд: Yamaha Страницы: 96
Yamaha X-MAX 400 ABS 2018 Owner'S Manual preview
X-MAX 400 ABS 2018
Бренд: Yamaha Страницы: 118
Yamaha Virago XV250T 2004 Owner'S Manual preview
Virago XV250T 2004
Бренд: Yamaha Страницы: 95
Yamaha V-star XVS65V Owner'S Manual preview
V-star XVS65V
Бренд: Yamaha Страницы: 103
Yamaha V-Star XVS11Y Owner'S Manual preview
V-Star XVS11Y
Бренд: Yamaha Страницы: 102
Yamaha V-star XVS65X Owner'S Manual preview
V-star XVS65X
Бренд: Yamaha Страницы: 104

Бренды по названию

Популярные бренды

Загрузить еще бренды