manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

cjlh

Fixings

1.

Electrical connector

2.

Instruments

3.

Refit the windscreen motor (see Windscreen Motor - Installation).
Reconnect the battery positive, (red) lead first and tighten the terminals to 

4.5 Nm

.

Refit the rider’s seat (see Rider’s Seat - Installation).

Headlight Bulb Replacement

Position Light Bulb Replacement

WARNING

Adjust road speed to suit the visibility and weather conditions in which the motorcycle is being operated.
Make sure that the head light beam is adjusted to illuminate the road surface sufficiently far ahead without
dazzling oncoming traffic. An incorrectly adjusted headlight may impair visibility causing an accident.

WARNING

Never attempt to adjust a headlight beam when the motorcycle is in motion.
Any attempt to adjust a headlight beam when the motorcycle is in motion may result in loss of control and an
accident.

CAUTION

Do not cover the headlight or lens with any item likely to obstruct air flow to, or prevent heat escaping from,
the headlight lens.
Covering the headlight lens during operation with items of clothing, luggage, adhesive tape, devices intended
to alter or adjust the headlight beam or non genuine headlight lens covers will cause the headlight lens to
overheat and distort, causing irreparable damage to the headlight assembly.
Damage caused by overheating is not considered a manufacturing defect and will not be covered under
warranty.
If the headlight must be covered during use - such as taping of the headlight lens required during
closed

‑

course conditions - the headlight must be disconnected.

Note

The headlight can be adjusted by means of vertical and horizontal adjustment screws located on the
rear of the headlight.

3

1

Tiger Explorer XR Series

713 of 746

ELECTRICAL

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

KAYO MOTOR T2 Service Manual preview
T2
Бренд: KAYO MOTOR Страницы: 61
A3 HELMET TroyLee Designs Owner'S Manual preview
TroyLee Designs
Бренд: A3 HELMET Страницы: 244
Triumph Bonneville T100 Owner'S Handbook Manual preview
Bonneville T100
Бренд: Triumph Страницы: 198
Suzuki 990D0-31J50-CLE Installation Instructions Manual preview
990D0-31J50-CLE
Бренд: Suzuki Страницы: 12
BMW HP2 ENDURO Manual preview
HP2 ENDURO
Бренд: BMW Страницы: 139
VStreamT Windscreen N20012A Installation And Owner'S Manual preview
Windscreen N20012A
Бренд: VStreamT Страницы: 3
GAS GAS TXT PRO - PART LIST 2005 Parts List preview
TXT PRO - PART LIST 2005
Бренд: GAS GAS Страницы: 38
BMW F 650 GS Manual preview
F 650 GS
Бренд: BMW Страницы: 88
Gemini 953 Installation And Use Manual preview
953
Бренд: Gemini Страницы: 20
Honda Gold Wing GL1100 Service Manual preview
Gold Wing GL1100
Бренд: Honda Страницы: 356
KTM 60112929050 Information preview
60112929050
Бренд: KTM Страницы: 7
Royal Enfield II Series Workshop Maintenance Manual preview
II Series
Бренд: Royal Enfield Страницы: 60
Royal Enfield Classic 350 2019 Owner'S Manual preview
Classic 350 2019
Бренд: Royal Enfield Страницы: 126
Laverda 500 Workshop Manual preview
500
Бренд: Laverda Страницы: 151
SHOEI HORNET ADV Instructions For Use Manual preview
HORNET ADV
Бренд: SHOEI Страницы: 42
R&G YTI0006BK Fitting Instructions preview
YTI0006BK
Бренд: R&G Страницы: 4
3M Speedglas G5-02 User Instructions preview
Speedglas G5-02
Бренд: 3M Страницы: 76
hepco & becker 6504531 00 01 Manual preview
6504531 00 01
Бренд: hepco & becker Страницы: 7

Бренды по названию

Популярные бренды

Загрузить еще бренды