manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Electrical System

Fuse

Rear electrical accessory socket (if fitted)

Top box electrical accessory socket (if fitted)

Cooling fan

PS5

Fuel pump

Starter solenoid

Horn

WARNING

Always replace blown fuses with new ones of the correct rating (as specified on the fuse box cover) and
never use a fuse of higher rating. Use of an incorrect fuse could lead to an electrical problem, resulting in
motorcycle damage, loss of motorcycle control and an accident.

If after resetting the automatic software protection system or replacing a blown fuse, a fault still persists,
investigate the cause and take remedial action as necessary.

Triumph Diagnostic Software - Chassis ECM

The chassis ECM has an on-board diagnostics feature which allows service technicians to retrieve stored data
using the Triumph diagnostic software. 

Full details of the Triumph diagnostic software operation and how

to interpret the results are given in the Triumph Diagnostic Tool User Guide.

The software is connected, via an interface cable, to the motorcycle using a dedicated diagnostic plug situated
beneath the seat. By using a dedicated plug, no electrical connectors associated with the system are disturbed,
reducing potential connector damage.
The software allows the user to retrieve data associated with the system sensors and actuators, test various
component functions, read build data and make minor adjustments to the set-up of the system. The data and
tests available are described on the following pages.

On-board Fault Detection System

The on-board diagnostic system has two stages to fault detection. When a fault is detected, the DSM
(Diagnostic Status Manager) raises a flag to indicate that a fault is present and increments a counter. The
counter checks the number of instances that the fault is noted.
When the count begins, the fault is detected but not confirmed. If the fault continues to be detected and the
count reaches a predetermined threshold, the fault becomes confirmed and a DTC (Diagnostic Trouble Code)
will be logged in the ECM's memory. A confirmed fault may be indicated by the effected system(s) simply
becoming inoperative, or by the illumination of a system warning light and/or instrument warning message. Once
a fault is confirmed, the number of ignition switch cycles made is counted. If the fault clears, the ignition switch
cycle counter will restore operation to the affected system(s) and extinguish any warning lights or instrument
messages at a predetermined count. DTCs are then erased from the ECM memory at another (higher) count.

To connect the Triumph diagnostic interface to the motorcycle, remove the rider’s seat (see Rider’s Seat -
Removal) and release the diagnostic connector from its locating tang.

1. 

1

Tiger Explorer XR Series

636 of 746

ELECTRICAL

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Yamaha WR250F(R) Owner'S Service Manual preview
WR250F(R)
Бренд: Yamaha Страницы: 860
Ohlins YA 469 Mounting Instructions preview
YA 469
Бренд: Ohlins Страницы: 4
BMW Motorrad F 900 XR Rider'S Manual preview
F 900 XR
Бренд: BMW Motorrad Страницы: 261
zeeltronic PDCI-30 User Manual preview
PDCI-30
Бренд: zeeltronic Страницы: 10
Cobra CX50FWE Manual preview
CX50FWE
Бренд: Cobra Страницы: 80
GAS GAS 2003 FSE Parts List preview
2003 FSE
Бренд: GAS GAS Страницы: 26
Bajaj pulsar F250 Owner'S Manual preview
pulsar F250
Бренд: Bajaj Страницы: 44
Yamaha XJ600SK Owner'S Manual preview
XJ600SK
Бренд: Yamaha Страницы: 110
DYNATEK D3K2-2 Installation Instructions preview
D3K2-2
Бренд: DYNATEK Страницы: 4
DYNATEK D2K-HD2 User Instructions preview
D2K-HD2
Бренд: DYNATEK Страницы: 5
Cliftech Design V-Gauge Lite Manual preview
V-Gauge Lite
Бренд: Cliftech Design Страницы: 24
DELTA-SPORT crivit sports 101545 Instructions For Use Manual preview
crivit sports 101545
Бренд: DELTA-SPORT Страницы: 42
Chicago Electric 64527 Owner'S Manual preview
64527
Бренд: Chicago Electric Страницы: 8
Chicago Electric 67854 Owners Manual & Safety Manual preview
67854
Бренд: Chicago Electric Страницы: 12
Ruroc LITE Instruction Manual preview
LITE
Бренд: Ruroc Страницы: 36
Benelli BN600 Owner'S Manual preview
BN600
Бренд: Benelli Страницы: 32
Benelli 125 Enduro Workshop Manual preview
125 Enduro
Бренд: Benelli Страницы: 77
Benelli TRK 502 2017 Owner'S Manual preview
TRK 502 2017
Бренд: Benelli Страницы: 469

Бренды по названию

Популярные бренды

Загрузить еще бренды