manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Note

Upon clicking START, the diagnostic tool will send a command to the chassis ECM to perform an
RSU preload motor calibration the next time the ignition is switched On.

Click start, then disconnect the Triumph Diagnostic Tool from the motorcycle.

4. 

Turn the ignition switch Off and allow the chassis ECM to power down. This should take approximately 10
seconds.

5. 

Turn the ignition switch On. The RSU preload motor calibration will start automatically. Do not start the
engine at this stage.

6. 

Note

The motorcycle must remain stationary during calibration. If the motorcycle is moved or ridden, this
will halt the calibration and cause the TSAS warning light to become illuminated. In this situation,
calibration will be restarted the next time the ignition switch is turned Off then On again.
During calibration, the TSAS warning light will flash and the message WARNING - TSAS SYSTEM
FAULT will be displayed in the instrument’s multifunction display.
This warning message can be cleared by pressing the SELECT button on the left handlebar switch
housing.
Upon clearing the warning message, the information message TSAS SYSTEM CALIBRATING -
PLEASE WAIT will be displayed.
Calibration is complete when the instrument messages clear and the TSAS warning light stops
flashing.

OFF-ROAD

WARNING

TSAS

SYSTEM FAULT

CHECK MANUAL

PRESS SELECT

TO CLEAR

1

2

3

Instrument message

1.

TSAS warning light

2.

SELECT button

3.

Wait for the TSAS warning light to stop flashing, indicating that the RSU preload motor calibration is
complete.

7. 

WARNING

Never start the engine or let it run for any length of time in a closed area. The exhaust fumes are poisonous
and may cause loss of consciousness and death within a short time. Always operate the motorcycle in the
open-air or in an area with adequate ventilation.

Start the engine and check that the TSAS warning light remains off. If the warning light resumes flashing, the
RSU preload motor is being recalibrated due to low battery voltage. Wait for the warning light to stop flashing
before turning the engine off.

8. 

When the calibration has successfully completed, reconnect the Triumph Diagnostic Tool and check for any
stored DTCs. Rectify as necessary.

9. 

Tiger Explorer XR Series

418 of 746

REAR SUSPENSION

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

ZARD ZUMA Fitting Manual preview
ZUMA
Бренд: ZARD Страницы: 2
LSL 507T068A Fitting Instruction preview
507T068A
Бренд: LSL Страницы: 4
MSA F2 X-TREM Operating Manual preview
F2 X-TREM
Бренд: MSA Страницы: 163
Suzuki 1987 GSX-R150 Service Manual preview
1987 GSX-R150
Бренд: Suzuki Страницы: 311
R&G ECS0126BK Fitting Instructions preview
ECS0126BK
Бренд: R&G Страницы: 2
X-lite X-902 Directions For Use Manual preview
X-902
Бренд: X-lite Страницы: 84
Pandora Smart Moto Manual preview
Smart Moto
Бренд: Pandora Страницы: 56
SC MOTO NOSTRA MN4602 Assembly Instructions Manual preview
MOTO NOSTRA MN4602
Бренд: SC Страницы: 8
Bosch DISBLAY DDU 7 Manual preview
DISBLAY DDU 7
Бренд: Bosch Страницы: 160
KTM Power Parts 69029096140 Manual preview
69029096140
Бренд: KTM Power Parts Страницы: 12
Yamaha 2004 Moto Matrix Supplementary Service Manual preview
2004 Moto Matrix
Бренд: Yamaha Страницы: 41
Yamaha 2004 YZ125F1 Parts Catalog preview
2004 YZ125F1
Бренд: Yamaha Страницы: 48
Yamaha 2003 TDM900 Supplementary Service Manual preview
2003 TDM900
Бренд: Yamaha Страницы: 28
Yamaha 2004 FJR1300(S) Supplementary Service Manual preview
2004 FJR1300(S)
Бренд: Yamaha Страницы: 44
Yamaha 2002 YZF-R6R Service Manual preview
2002 YZF-R6R
Бренд: Yamaha Страницы: 30
Yamaha 2006 YSF-R1(V) Supplementary Service Manual preview
2006 YSF-R1(V)
Бренд: Yamaha Страницы: 87
Yamaha 2006 YBR125 Owner'S Manual preview
2006 YBR125
Бренд: Yamaha Страницы: 84
Yamaha 2006 YZFR6V Owner'S Manual preview
2006 YZFR6V
Бренд: Yamaha Страницы: 106

Бренды по названию

Популярные бренды

Загрузить еще бренды