manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Remove the fixings and lift off the release plate. Collect the springs.

2. 

Remove the clutch centre.

3.

Note

The one outermost and two innermost friction plates differ from the six centre plates and must not
be fitted in any other positions.
The innermost steel plate differs from the seven other steel plates and cannot be fitted in any other
position.

Noting their orientation, remove all the clutch friction plates and steel plates together with the anti-judder
spring and anti-judder seat washer.

4. 

Note

Record the orientation of all components as they are removed. The plates must be assembled in the
same order.

1

2

3

4

5

6

7

8

9

Clutch Centre

1.

Anti-judder seat washer

2.

Anti-judder spring

3.

Outer friction plate

4.

7 x centre steel plates

5.

6 x centre friction plates

6.

Inner friction plates

7.

Inner steel plate

8.

Pressure plate

9.

Friction Plate Inspection

Thickness

If any friction plate thickness is outside the service limit, replace the friction plates as a set.

1.

Tiger Explorer XR Series

130 of 746

CLUTCH

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

N-Com R Series User Instructions And Safety preview
R Series
Бренд: N-Com Страницы: 28
HRC '92-RS125R Owner'S Manual preview
'92-RS125R
Бренд: HRC Страницы: 88
N-Com SPCOM00000100 Quick Start Manual preview
SPCOM00000100
Бренд: N-Com Страницы: 6
Paaschburg & Wunderlich HIGHSIDER VICTORY Mounting And Safety Instructions preview
HIGHSIDER VICTORY
Бренд: Paaschburg & Wunderlich Страницы: 5
DYNATEK D3K1-4 Installation Instructions preview
D3K1-4
Бренд: DYNATEK Страницы: 3
DYNATEK D2K-HD1 User Instructions preview
D2K-HD1
Бренд: DYNATEK Страницы: 8
hepco & becker 611.793 00 02 Assembling Instructions preview
611.793 00 02
Бренд: hepco & becker Страницы: 4
R&G FI0119BK Fitting Instructions Manual preview
FI0119BK
Бренд: R&G Страницы: 6
Sealey FPS6 Instructions preview
FPS6
Бренд: Sealey Страницы: 2
Bagster AP 3076 Fitting Instructions preview
AP 3076
Бренд: Bagster Страницы: 2
RIEJU MRT 50 EURO 5 Owner'S Manual preview
MRT 50 EURO 5
Бренд: RIEJU Страницы: 52
Ruroc LITE Instruction Manual preview
LITE
Бренд: Ruroc Страницы: 36
R&G AB0053 Fitting Instructions Manual preview
AB0053
Бренд: R&G Страницы: 19
PORTMAN APSPS1 User Manual preview
APSPS1
Бренд: PORTMAN Страницы: 13
Beta 350-498 RR Setup Manual preview
350-498 RR
Бренд: Beta Страницы: 5
Abus PEDELEC Instruction Manual preview
PEDELEC
Бренд: Abus Страницы: 6
Jackson SureWerx WH30 ALBATROSS Manual preview
SureWerx WH30 ALBATROSS
Бренд: Jackson Страницы: 8
Honda CM 185T 1981 Manual preview
CM 185T 1981
Бренд: Honda Страницы: 206

Бренды по названию

Популярные бренды

Загрузить еще бренды