manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Brake pads

1.

Anti-rattle spring

2.

Rear Brake Pads - Installation

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

WARNING

Never use mineral-based grease (such as lithium or copper based grease) in any area where contact with
the braking system hydraulic seals and dust seals is possible. Mineral-based grease will damage the
hydraulic seals and dust seals in the calipers and master cylinders.
Damage caused by contact with mineral-based grease may reduce braking efficiency resulting in loss of
motorcycle control and an accident.

CAUTION

To prevent paint damage, do not spill brake fluid onto any area of the bodywork. Spilled brake fluid will
damage paintwork.

If fitting new pads, use hand pressure to compress the caliper piston fully into its bore.

1.

Fit the anti-rattle spring into the caliper.

2.

Renew the brake pads as a pair or, if both pads are in a serviceable condition, clean the pad grooves before
fitting them.

3. 

Fit the brake pads to the caliper in the positions noted during removal.

4.

WARNING

Do not apply more than a minimum coating of grease to the brake pad retaining pins. Excess grease may
contaminate the brake pads, hydraulic seals and discs causing reduced braking efficiency and an accident.

Lubricate the brake pad retaining pin using a minimum amount of proprietary high temperature copper
based grease. Press down on both pads and fit the retaining pins.

5. 

Position the caliper over the disc ensuring both pads are correctly fitted.

6.

Fit the caliper bolts and tighten to 

40 Nm

.

7.

Tighten the brake pad retaining pin to 

17 Nm

.

8.

Pump the brake pedal to correctly position the caliper pistons.

9.

Check the brake fluid level in the rear reservoir and top-up as required with new DOT 4 fluid.

10.

WARNING

Use only DOT 4 specification brake fluid as listed in the General Information section of this manual. The use
of brake fluids other than those DOT 4 fluids listed in the General Information section may reduce the
efficiency of the braking system leading to loss of motorcycle control and an accident.
Observe the brake fluid handling warnings given earlier in this section of the manual.

Check for correct brake operation. Rectify as necessary.

11.

WARNING

Tiger Explorer XR Series

484 of 746

BRAKES

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

N-Com R Series User Instructions And Safety preview
R Series
Бренд: N-Com Страницы: 28
Racelogic VBOX Video HD2 Assembly Manual preview
VBOX Video HD2
Бренд: Racelogic Страницы: 2
Coleman Powersports CT200U Owner'S Manual preview
Powersports CT200U
Бренд: Coleman Страницы: 37
R&G FI0054BK Fitting Instructions preview
FI0054BK
Бренд: R&G Страницы: 4
GAS GAS FSE 450 - 2006 User Manual preview
FSE 450 - 2006
Бренд: GAS GAS Страницы: 72
Velmia Premium Motorcycle Cover Instructions For Use Manual preview
Premium Motorcycle Cover
Бренд: Velmia Страницы: 32
hepco & becker 5017591 00 01 Manual preview
5017591 00 01
Бренд: hepco & becker Страницы: 5
KTM Freeride 350 AUS Setup Instructions preview
Freeride 350 AUS
Бренд: KTM Страницы: 25
Rekluse CoreManual TorqDrive Installation & User Manual preview
CoreManual TorqDrive
Бренд: Rekluse Страницы: 20
HERO ACHIEVER 150 Manual preview
ACHIEVER 150
Бренд: HERO Страницы: 68
rizoma BS211 User Manual preview
BS211
Бренд: rizoma Страницы: 14
Ducati SUPERSPORT1000 2003 Owner'S Manual preview
SUPERSPORT1000 2003
Бренд: Ducati Страницы: 328
Yamaha YZFR1Y(C) Owner'S Manual preview
YZFR1Y(C)
Бренд: Yamaha Страницы: 122
Yamaha YZF R1 2020 Owner'S Manual preview
YZF R1 2020
Бренд: Yamaha Страницы: 142
Yamaha YZFR6W Owner'S Manual preview
YZFR6W
Бренд: Yamaha Страницы: 118
hepco & becker 506.667 Quick Start Manual preview
506.667
Бренд: hepco & becker Страницы: 4
Arai QUANTUM-X Operation Instructions Manual preview
QUANTUM-X
Бренд: Arai Страницы: 12
Yamasaki YM50-8B User Manual preview
YM50-8B
Бренд: Yamasaki Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды