manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

release the brake lever.
Repeat steps 3 to 5 until no more air appears in the bleed tube.

6. 

Note

Maintain the brake fluid level between the upper and lower reservoir levels whilst bleeding is being
carried out.

When all air has been expelled from the system, hold the lever fully against the handlebar and close the
bleed nipple.

7. 

Tighten the bleed nipple to 

6 Nm

.

8.

Repeat the procedure for the right hand caliper.

9.

Note

If the manual bleed procedure is to be followed by an ABS system bleed, leave the transparent tube
and receptacle in place on the right hand caliper.

ABS System Bleed Procedure

Connect the Triumph diagnostic tool (see System Diagnostics).

1.

Follow the on screen menu to ABS Diagnostics. From the menu, select 'BLEED SYSTEM' (see the Triumph
Diagnostic Tool User Guide).

2. 

Note

On pressing the Start button, the diagnostic software will send a command to the ABS ECM to begin
the ABS bleed sequence.
The bleed sequence lasts for 140 seconds and consists of three stages; Flush stage, Bleed stage 1
and Bleed stage 2.
The bleed sequence can be stopped at any time by pressing the Stop button on the diagnostic
software.

Press the Start button to activate the bleed sequence on the diagnostic tool.

3.

Note

The flush stage lasts for 20 seconds. The ABS modulator can be heard operating during the flush
stage and will become silent when flush stage has completed.

With bleed nipples closed, repeatedly operate the front brake lever for the duration of the flush stage.

4.

Note

Bleed stage 1 will start when the flush stage has completed and will be automatically followed by
bleed stage 2.
Bleed stages 1 and 2 last for 60 seconds each. The ABS modulator will remain silent during bleed
stage 1 but can be heard operating during bleed stage 2.

Release the right hand caliper bleed nipple.

5.

Note

During bleeding, do not allow the fluid level to fall below the lower level mark in the reservoir. If the
fluid level is allowed to fall below this mark, air may enter the system and the sequence of bleeding
must be repeated.

Get an assistant to slowly pull the brake lever to the handlebar.

6.

With the lever held fully against the handlebar, close the bleed nipple. Once the bleed nipple is closed,
release the brake lever.

7. 

Repeat steps 5 to 7 for the duration of bleed stages 1 and 2.

8.

Note

Maintain the brake fluid level between the upper and lower reservoir levels whilst bleeding is being
carried out.

Once the bleed sequence has completed the diagnostic tool will display a message 

'ABS system bleed

complete'

. Note that this message may take a few seconds to appear after the ABS modulator has become

9. 

Tiger Explorer XR Series

465 of 746

BRAKES

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

R&G CP0479 Fitting Instructions Manual preview
CP0479
Бренд: R&G Страницы: 13
Suzuki VX800L Manual preview
VX800L
Бренд: Suzuki Страницы: 101
Surtek CSS01 User Manual And Warranty preview
CSS01
Бренд: Surtek Страницы: 12
Faller 190119/1 Manual preview
190119/1
Бренд: Faller Страницы: 8
Coolster POCKET BIKE QG-40 User Manual preview
POCKET BIKE QG-40
Бренд: Coolster Страницы: 13
Fuelpak SOFTAIL 2012 Instructions preview
SOFTAIL 2012
Бренд: Fuelpak Страницы: 2
Hermes LCD 9.13G Manual preview
LCD 9.13G
Бренд: Hermes Страницы: 23
Benelli Leoncino Owner'S Manual preview
Leoncino
Бренд: Benelli Страницы: 464
Benelli TORNADO NAKED TNT125 Owner'S Manual preview
TORNADO NAKED TNT125
Бренд: Benelli Страницы: 530
Honda CRF 450B Quick Start Manual preview
CRF 450B
Бренд: Honda Страницы: 8
Protos Integral IN Manual preview
Integral IN
Бренд: Protos Страницы: 52
hepco & becker 700554 00 01 Quick Start Manual preview
700554 00 01
Бренд: hepco & becker Страницы: 2
KTM 450 SMR Owner'S Manual preview
450 SMR
Бренд: KTM Страницы: 100
Gazzini 10039625 Instructions For Use Manual preview
10039625
Бренд: Gazzini Страницы: 35
KTM 90112927044 Information preview
90112927044
Бренд: KTM Страницы: 7
KTM 90111942044 Information preview
90111942044
Бренд: KTM Страницы: 12
KTM 79011955044 Information preview
79011955044
Бренд: KTM Страницы: 22
GripOne S3 Manual preview
S3
Бренд: GripOne Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды