manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Target dwell time

The actual time from coil 'on' to coil 'off'.

TDC

Top Dead Centre.

Throttle actuator motor

Motor used to open/close the throttle.

Throttle position

The position of the throttle butterfly given as a percentage of the movement range. When the data is displayed
on the tool, fully open need not be 100% nor fully closed 0%.

Throttle position sensor

Sensor for the primary throttle position.

Throttle Voltage

Voltage at the throttle potentiometer.

TPMS

Tyre Pressure Monitoring System.

Transponder

A transmitter-responder chip located in the ignition key. The transponder is activated by a radio signal sent out
by the immobiliser and TPMS control module, via an antenna located around the ignition switch. If the
immobiliser and TPMS control module does not receive the correct code signal from the transponder, the
immobiliser will remain active and the engine will not start.

Twist grip position sensor

The twist grip position sensor is used to relay twist grip position information to the ECM. The ECM uses this
information to drive the throttle actuator motor to the correct position.

Vbatt

Battery Voltage.
This model is fitted with an electronic engine management system which encompasses control of both ignition
and fuel delivery. The engine ECM is electronically paired to the chassis ECM to help prevent theft of the
motorcycle (see Immobiliser System). The engine ECM also draws information from sensors positioned around
the engine, cooling and air intake systems and precisely calculates ignition advance and fuelling requirements
for all engine speeds and loads.
In addition, the system has an on-board diagnostic function. This ensures that, should a malfunction occur in the
engine management system, the malfunction type, and engine data at the time the malfunction occurred, are
stored in the engine ECM memory. This stored data can then be recovered using a special service tool which is
mandatory for all Triumph dealers. In this way, precise diagnosis of a fault can be made and the fault quickly
rectified.

Intake air temperature sensor

 - situated in the top of the airbox. As the density of the air (and therefore the

amount of oxygen available to ignite the fuel) changes with temperature, an intake air temperature sensor is
fitted. Changes in air temperature (and therefore air density) are compensated for by adjusting the amount of
fuel injected to a level consistent with clean combustion and low emissions.

Ambient air pressure sensor

 - situated on the right hand side of the rear mudguard, beneath the seat. The

ambient air pressure sensor measures atmospheric air pressure. With this information, the amount of fuel per

Tiger Explorer XR Series

235 of 746

FUEL SYSTEM / ENGINE MANAGEMENT

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Yamaha YZ85G Owner'S Manual preview
YZ85G
Бренд: Yamaha Страницы: 88
Takegawa 09-12-1010 Instruction Manual preview
09-12-1010
Бренд: Takegawa Страницы: 2
Suzuki 1987 GSX-R150 Service Manual preview
1987 GSX-R150
Бренд: Suzuki Страницы: 311
R&G CP0485 Fitting Instructions Manual preview
CP0485
Бренд: R&G Страницы: 47
KSR Moto GRS125 2013 User Manual preview
GRS125 2013
Бренд: KSR Moto Страницы: 51
Victory Motorcycles 2016 Empulse TT Rider'S Manual preview
2016 Empulse TT
Бренд: Victory Motorcycles Страницы: 138
Isotta SP8106 R1200R Fitting Instructions preview
SP8106 R1200R
Бренд: Isotta Страницы: 2
Honda C8R600F4 Service Manual preview
C8R600F4
Бренд: Honda Страницы: 362
KTM 690 Enduro AUS 2010 Repair Manual preview
690 Enduro AUS 2010
Бренд: KTM Страницы: 265
Maico GM STAR 250 1986 Owner'S Manual preview
GM STAR 250 1986
Бренд: Maico Страницы: 32
hepco & becker 6304554 00 01 Quick Start Manual preview
6304554 00 01
Бренд: hepco & becker Страницы: 4
Husqvarna 28512027000 Information preview
28512027000
Бренд: Husqvarna Страницы: 12
Husqvarna 27035936044 Information preview
27035936044
Бренд: Husqvarna Страницы: 12
Husqvarna 28012979044 Information preview
28012979044
Бренд: Husqvarna Страницы: 7
Husqvarna 28508915044 Information preview
28508915044
Бренд: Husqvarna Страницы: 32
Husqvarna 9301395014430 Information preview
9301395014430
Бренд: Husqvarna Страницы: 7
Husqvarna H300 Product User Manual preview
H300
Бренд: Husqvarna Страницы: 128
hepco & becker 611.793 00 02 Assembling Instructions preview
611.793 00 02
Бренд: hepco & becker Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды