manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

must not use the tyre pressure display on the instruments.

WARNING

The tyre pressure monitoring system is not to be used as a tyre pressure gauge when adjusting the tyre
pressures. For correct tyre pressures, always check the tyre pressures when the tyres are cold and using an
accurate tyre pressure gauge.
Use of the TPMS system to set inflation pressures may lead to incorrect tyre pressures leading to loss of
motorcycle control and an accident.

When fitting the TPMS, the installation flow-chart detailed in the Triumph Diagnostic Tool User Guide must be
followed.

System Components and Operation

Instruments

 - used to display the tyre pressure value, the tyre symbol and the TPMS warning light.

Chassis ECM

 - receives the data from the tyre pressure sensors and sends the information to the

instrument pack.

Tyre pressure sensor

 - situated inside the front and rear wheel. Each sensor has its own unique ID number

and must be recorded in the spaces provided in the Owner’s Handbook. These sensors measure the air
pressure inside the tyre and transmit pressure data to the instruments. These sensors will not transmit the
data until the motorcycle is travelling at a speed of approximately 12 mph (20 km/h). Two dashes will be
visible in the display area until the tyre pressure signal is received. The wheel sensor is a sealed unit and
must not be opened. The battery inside the sensor is not replaceable and a new sensor must be fitted when
the battery Voltage becomes too low.

Compliance

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired
operation.

Changes or modifications to the device could void the user's authority to operate the equipment.

Diagnostics

When a fault condition with the TPMS is detected, the red warning light in the instrument pack will illuminate and
a warning message may be displayed on the instrument’s display screen.
The red warning light and flashing symbol will also occur if the TPMS has been enabled in the instrument pack
but not in the chassis ECM. Before proceeding to the diagnostics, check that the motorcycle has wheel sensors
fitted and that the option for the TPMS has been enabled in the chassis ECM.

Further Diagnosis

The diagnostic trouble code tables, if used correctly, help to pinpoint a fault in the system once a diagnostic
trouble code has been stored (see Chassis ECM Diagnostic Trouble Codes

TPMS Components Locations

Tiger Explorer XR Series

240 of 746

FUEL SYSTEM / ENGINE MANAGEMENT

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Dowco Fastrax 50144-00 Installation Instructions preview
Fastrax 50144-00
Бренд: Dowco Страницы: 3
Denali SoundBomb TT-SB.10100.B Instruction Manual preview
SoundBomb TT-SB.10100.B
Бренд: Denali Страницы: 3
Pagsta BOBBER User Manual preview
BOBBER
Бренд: Pagsta Страницы: 47
Kinderkraft SAFETY User Manual preview
SAFETY
Бренд: Kinderkraft Страницы: 36
BMS Cavalier 150 Owner'S Manual preview
Cavalier 150
Бренд: BMS Страницы: 12
tucanourbano TERMOSCUD R184 Instruction Manual preview
TERMOSCUD R184
Бренд: tucanourbano Страницы: 4
Sealey PWH699R Instructions preview
PWH699R
Бренд: Sealey Страницы: 4
Kinroad XT50GY User Manual preview
XT50GY
Бренд: Kinroad Страницы: 28
Honda CM400E 1981 Owner'S Manual preview
CM400E 1981
Бренд: Honda Страницы: 43
hepco & becker 700427 Quick Start Manual preview
700427
Бренд: hepco & becker Страницы: 2
APRILIA RS4 125 Service Manual preview
RS4 125
Бренд: APRILIA Страницы: 155
APRILIA PEGASO 650 STRADA Service Station Manual preview
PEGASO 650 STRADA
Бренд: APRILIA Страницы: 236
Electronicbox D-Box Installation Manual preview
D-Box
Бренд: Electronicbox Страницы: 2
KTM 250 DUKE Owner'S Manual preview
250 DUKE
Бренд: KTM Страницы: 186
Indian Motorcycle Indian Scout Rider'S Manual preview
Indian Scout
Бренд: Indian Motorcycle Страницы: 122
orcal ASTOR Manual preview
ASTOR
Бренд: orcal Страницы: 75
PIAGGIO X7 125 2012 Manual preview
X7 125 2012
Бренд: PIAGGIO Страницы: 92
EWM Powershield 2.5 Manual preview
Powershield 2.5
Бренд: EWM Страницы: 40

Бренды по названию

Популярные бренды

Загрузить еще бренды