manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

General Frame Inspection

Passenger Seat - Removal

Passenger Seat - Installation

Inspect the frame, bodywork and footrests for accident and other damage, cracks, splits and general
dilapidation. Check all fixings for security. If any faults are found, rectify as necessary. If any faults with the
frame are found, the frame must be replaced; repairs to the frame are not permitted.

1. 

WARNING

If the motorcycle is involved in an accident or collision it must be taken to an authorised Triumph dealer for
inspection and repair before it is ridden again.

WARNING

The frame must not be modified in any way. Any modification to the frame, such as welding or drilling, may
weaken the structure causing an unsafe riding condition leading to loss of motorcycle control and an
accident.

Check the operation of the side stand to make sure it is securely held in the retracted position by the spring.
Rectify any faults.

2. 

WARNING

If the return spring is faulty, the side stand could extend whilst the motorcycle is being ridden. This will cause
an unsafe riding condition, which could lead to loss of motorcycle control and an accident.

If fitted, check the operation of the centre stand to make sure it is securely held in the retracted position by
the spring. Rectify any faults

3. 

WARNING

If the return spring is faulty, the centre stand will not be held in the retracted position whilst the motorcycle is
being ridden. This will cause an unsafe riding condition, which could lead to loss of motorcycle control and an
accident.

CAUTION

To prevent damage to the seats or seat covers, care must be taken not to drop the seats. Do not lean the
seats against the motorcycle or any surface which may damage the seats or seat covers. Instead, place the
seats, with the seat cover facing upwards, on a clean, flat surface which is covered with a soft cloth.
Do not place any item on the seats which may cause damage or staining to the seat covers.

The passenger seat lock is located on the rear mudguard, below the rear light unit. To remove the seat,
insert the ignition key into the seat lock and turn it anticlockwise while pressing down on the rear of the seat.
This will release the seat from its lock and allow it to be slid rearwards. If equipped with heated seats,
disconnect the heated seat’s electrical connector for complete removal from the motorcycle.

1. 

Tiger Explorer XR Series

565 of 746

FRAME / BODYWORK

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Honda V-TWIN CUSTOM Owner'S Manual preview
V-TWIN CUSTOM
Бренд: Honda Страницы: 112
Cobra 602-3000 Instruction Manual preview
602-3000
Бренд: Cobra Страницы: 2
hepco & becker 6317588 00 01L Quick Start Manual preview
6317588 00 01L
Бренд: hepco & becker Страницы: 3
Yamaha YZFR6X(C) Owner'S Manual preview
YZFR6X(C)
Бренд: Yamaha Страницы: 120
DYNATEK DDK2-8 Installation & User Manual preview
DDK2-8
Бренд: DYNATEK Страницы: 11
Malossi DARK SMOKE SPORT Fitting Instructions preview
DARK SMOKE SPORT
Бренд: Malossi Страницы: 4
hepco & becker 506998 00 01 Quick Start Manual preview
506998 00 01
Бренд: hepco & becker Страницы: 2
hepco & becker 610060 00 01 Manual preview
610060 00 01
Бренд: hepco & becker Страницы: 3
Memphis Shades MEM-9890 Mounting Instructions preview
MEM-9890
Бренд: Memphis Shades Страницы: 2
Memphis Shades 2321-0045 Mounting Instructions preview
2321-0045
Бренд: Memphis Shades Страницы: 2
Memphis Shades 2320-0037 Mounting Instructions preview
2320-0037
Бренд: Memphis Shades Страницы: 2
Wunderlich 31000-301 Fitting Instruction preview
31000-301
Бренд: Wunderlich Страницы: 4
Benelli 2014 BN600 Service Manual preview
2014 BN600
Бренд: Benelli Страницы: 243
Petzl ECRIN ROC A01 Product Information preview
ECRIN ROC A01
Бренд: Petzl Страницы: 4
hepco & becker 6617569 01 01 Manual preview
6617569 01 01
Бренд: hepco & becker Страницы: 4
hepco & becker 8007601 00 01 Manual preview
8007601 00 01
Бренд: hepco & becker Страницы: 3
KTM 60435940044 Manual preview
60435940044
Бренд: KTM Страницы: 7
Conrad 2564529 Operating Instructions preview
2564529
Бренд: Conrad Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды