manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

3880160 -T0301 - Fork Oil Filler/Evacuator

1. 

Adjustment plate

2.

Scale area

3.

Hole (zero position)

4.

Note

Zero level on the tool is set at the small exit hole in the side of the scale tube, NOT AT THE END TIP.
Do not attempt to block this side hole as this will cause the final fluid level to be incorrect.

Insert the scale end of the tool into the fork inner tube.

5.

Hold the tool adjuster plate level with the upper surface of the fork outer tube and draw fluid into the syringe
until fluid flow ceases (empty the syringe if the body becomes full before fluid flow stops).

6. 

The fluid level in the fork is now set to the height set on the tool scale. Check the tool scale setting and
repeat the process if incorrectly set.

7. 

WARNING

Incorrect fork oil levels could result in an unsafe riding condition leading to loss of control and an accident.

Assemble the fork (see Front Fork - Assembly).

8.

Refit the fork (see Front Fork - Installation).

9.

Fork Oil Level Chart

Oil Level*

Oil Volume

Oil Grade

105 mm

700 cc

WP 4860-1166 SAE4

*Fork fully compressed with spring guide, upper spring preload spacer(s) and spring removed.

Front Fork - Disassembly

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

WARNING

If the damping cylinder is to be removed, we recommend that one fork is disassembled and assembled prior
to starting work on the other. The damping cylinder in the left hand fork is for compression damping while the
damping cylinder in the right hand fork is for rebound damping. Should these damping components get fitted
to the wrong fork, the front suspension will not function correctly and may lead to loss of motorcycle control
and an accident.

Turn the ignition on and note the instrument TSAS mode and damping setting so that the system can be
restored to its original setting upon re-assembly.
Set the TSAS damping to its softest (comfort) setting as described in the Owner’s Handbook.

Note

When removing the forks, ensure the top cap is loosened as described in Front Fork - Removal.
The fork seals can be renewed without removal of the damping cylinder. Unless removal of the
damping cylinder is necessary, omit step 24 of this procedure.
If the damping cylinder is to be removed, ensure the lower damping cylinder bolt is loosened as

Tiger Explorer XR Series

378 of 746

FRONT SUSPENSION

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

hepco & becker 651665 00 22-00-40 Manual preview
651665 00 22-00-40
Бренд: hepco & becker Страницы: 5
Honda VT750CD ACE Electrical Repair And Modification preview
VT750CD ACE
Бренд: Honda Страницы: 25
KTM F9903SE Setup Instructions preview
F9903SE
Бренд: KTM Страницы: 25
GAS GAS 2007 enducross EC User Manual preview
2007 enducross EC
Бренд: GAS GAS Страницы: 72
RDMOTO CF124 Quick Start Manual preview
CF124
Бренд: RDMOTO Страницы: 2
PIAGGIO NRG 50 User Manual preview
NRG 50
Бренд: PIAGGIO Страницы: 275
Gilera Fuoco 500 Service Station Manual preview
Fuoco 500
Бренд: Gilera Страницы: 396
MOTO GUZZI V7 CLASSIC Service Manual preview
V7 CLASSIC
Бренд: MOTO GUZZI Страницы: 134
Memphis Shades 2320-0032 Mounting Instructions preview
2320-0032
Бренд: Memphis Shades Страницы: 2
Razor Crazy Cart XL Replacement Instructions preview
Crazy Cart XL
Бренд: Razor Страницы: 3
Tool it 037786 Manual preview
037786
Бренд: Tool it Страницы: 26
Vetter Terraplane Driver'S/Owner'S Manual preview
Terraplane
Бренд: Vetter Страницы: 11
Royal Enfield Rumbler 500 2017 Manual preview
Rumbler 500 2017
Бренд: Royal Enfield Страницы: 160
APRILIA ETX 125 Manual preview
ETX 125
Бренд: APRILIA Страницы: 80
APRILIA DORSODURO Manual preview
DORSODURO
Бренд: APRILIA Страницы: 235
Vento Phantom R4i Service Maintenance Manual preview
Phantom R4i
Бренд: Vento Страницы: 88
APRILIA MOJITO 125 Manual preview
MOJITO 125
Бренд: APRILIA Страницы: 576
KTM 58612027050 Mounting Instructions preview
58612027050
Бренд: KTM Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды