manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

WARNING

Accurate wheel balance is important for safe, stable handling of the motorcycle. Do not remove or change
any wheel balance weights. Incorrect wheel balance may cause instability leading to loss of motorcycle
control and an accident.
When wheel balancing is required, such as after tyre replacement, see your authorised Triumph dealer.
Only use self-adhesive weights. Clip-on weights will damage the wheel and tyre potentially resulting in tyre
deflation, loss of motorcycle control and an accident.

WARNING

When replacement tyres are required, consult your authorised Triumph dealer who will arrange for the tyres
to be fitted according to the tyre manufacturer’s instructions.
When tyres are replaced, allow time for the tyre to seat itself to the rim (approximately 24 hours). During this
seating period, ride cautiously as an incorrectly seated tyre could cause loss of motorcycle control or an
accident. Initially, the new tyre will not produce the same handling characteristics as the worn tyre and the
rider must allow adequate riding distance (approximately 100 miles/160 km) to become accustomed to the
new handling characteristics.
After both 24 hours and 100 miles (160 km), the tyre pressures should be checked and adjusted and the tyre
examined for correct seating and rectified as necessary.
Use of a motorcycle when not accustomed to its handling characteristics, with incorrect tyre pressures or an
incorrectly seated tyre is dangerous and may lead to loss of motorcycle control and an accident.

Front Wheel - Removal

Front Wheel Bearings - Removal

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

Position the motorcycle on a paddock stand.

1.

Raise and support the front of the motorcycle.

2.

WARNING

Do not allow the calipers to hang on the brake hoses as this may damage the hoses.
Damaged hoses could cause brake failure leading to loss of control and an accident.

Note

It is not necessary to disconnect the brake hoses.

Detach and support the front brake calipers such that the weight of the caliper is not supported by the brake
hose (see Front Brake Caliper - Removal).

3. 

Loosen both pinch bolts at the lower end of the right hand fork.

4.

Tiger Explorer XR Series

549 of 746

WHEELS / TYRES

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Fantic Motor 125 Series Owner'S Manual preview
125 Series
Бренд: Fantic Motor Страницы: 130
R&G ECC0364R Fitting Instructions Manual preview
ECC0364R
Бренд: R&G Страницы: 6
National Cycle N936 Owner'S Manual preview
N936
Бренд: National Cycle Страницы: 2
KTM Super Adventure 2016 Setup Instructions preview
Super Adventure 2016
Бренд: KTM Страницы: 25
Regal Raptor DAYTONA 125 User Manual preview
DAYTONA 125
Бренд: Regal Raptor Страницы: 48
Honda 1999 Shadow Aero VT1100C3 Owner'S Manual preview
1999 Shadow Aero VT1100C3
Бренд: Honda Страницы: 226
hepco & becker 6513515 00 22-00-40 Manual preview
6513515 00 22-00-40
Бренд: hepco & becker Страницы: 7
Ducati SUPERSPORT1000 2003 Owner'S Manual preview
SUPERSPORT1000 2003
Бренд: Ducati Страницы: 328
KTM 690 Enduro AUS 2010 Repair Manual preview
690 Enduro AUS 2010
Бренд: KTM Страницы: 265
DYNATEK DDK3-3 Installation Manual preview
DDK3-3
Бренд: DYNATEK Страницы: 12
GAS GAS 2007 PAMPERA 450 Manual preview
2007 PAMPERA 450
Бренд: GAS GAS Страницы: 66
Yamaha YBR125ESD Owner'S Manual preview
YBR125ESD
Бренд: Yamaha Страницы: 82
Yamaha YBR125 Custom Owner'S Manual preview
YBR125 Custom
Бренд: Yamaha Страницы: 84
Yamaha YBR125ED Owner'S Manual preview
YBR125ED
Бренд: Yamaha Страницы: 90
Yamaha YBR 125K Owner'S Manual preview
YBR 125K
Бренд: Yamaha Страницы: 83
Yamaha YZ250 2021 Owner'S Manual preview
YZ250 2021
Бренд: Yamaha Страницы: 148
Yamaha Y15ZR Owner'S Manual preview
Y15ZR
Бренд: Yamaha Страницы: 96
Yamaha Y16ZR 2021 Owner'S Manual preview
Y16ZR 2021
Бренд: Yamaha Страницы: 108

Бренды по названию

Популярные бренды

Загрузить еще бренды