manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Note

Connecting rod bolts and nuts are treated with an anti-rust solution which must not be removed.
Clean the connecting rod with high flash-point solvent.
Remove all bearings and inspect for damage, wear and any signs of deterioration and replace as
necessary.

WARNING

Connecting rod bolts and nuts MUST only be used once. If the bolts or nuts are removed or undone for any
reason, new bolts and nuts MUST always be used.
Reusing bolts can cause connecting rods and their caps to detach from the crankshaft causing severe
engine damage, loss of motorcycle control and an accident.

Fit new connecting rod bolts to the big end.

1. 

Note

Ensure the piston is fitted correctly to the connecting rod.
If a previously run engine is being rebuilt, always ensure that the piston and connecting rod are
assembled in the same orientation as prior to strip-down.
Connecting rods may be fitted to the pistons either way around. However, ensure all three are fitted
facing the same way in relation to the piston. To aid correct assembly, the connecting rods have
assembly markers cast in to them, as shown overleaf.

Fit the pistons to the connecting rods (see Piston Assembly), ensuring the assembly markers will all be
assembled on the same side, when the piston arrows face the front of the engine.

2. 

1

chdx

Assembly markers

1.

WARNING

Avoid contact with the bearing surfaces of the bearing shells with engine components, tools, hands or
fingers. Damage to the soft bearing surfaces may result, leading to reduced engine life or severe engine
damage.

Select the correct big end bearing shells (see Connecting Rod Bearing Selection/ Crankshaft Journal Wear
Check).

3. 

Fit the bearing shells as selected at step 3 to the connecting rod and big end cap and lubricate with a 50/50
solution of engine oil and molybdenum disulphide grease.

4. 

Align the connecting rod to the crankshaft and fit the big end cap. Ensure the assembly marker on the
connecting rod and cap face the same direction.

5. 

Tiger Explorer XR Series

149 of 746

CRANKSHAFT / RODS / PISTONS

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Öhlins SD 053 Mounting Instructions preview
SD 053
Бренд: Öhlins Страницы: 8
X-lite X-402 T Safety And Instructions For Use preview
X-402 T
Бренд: X-lite Страницы: 96
W&W Cycles 13-815 Quick Start Manual preview
13-815
Бренд: W&W Cycles Страницы: 5
Cake Kalk Manual preview
Kalk
Бренд: Cake Страницы: 12
KTM 690 SMC R 2016 Series Setup Instructions preview
690 SMC R 2016 Series
Бренд: KTM Страницы: 18
Yamaha Star XV250Y Owner'S Manual preview
Star XV250Y
Бренд: Yamaha Страницы: 94
Yamaha Star XVS13CG 2015 Owner'S Manual preview
Star XVS13CG 2015
Бренд: Yamaha Страницы: 98
Yamaha Star XV250G 2015 Owner'S Manual preview
Star XV250G 2015
Бренд: Yamaha Страницы: 88
Yamaha Star XVS13CTD 2012 Owner'S Manual preview
Star XVS13CTD 2012
Бренд: Yamaha Страницы: 104
Yamaha Star XVS11X Owner'S Manual preview
Star XVS11X
Бренд: Yamaha Страницы: 104
Yamaha Star XV250H 2016 Owner'S Manual preview
Star XV250H 2016
Бренд: Yamaha Страницы: 98
Yamaha Star XVS95B Owner'S Manual preview
Star XVS95B
Бренд: Yamaha Страницы: 98
Yamaha YZ65 2021 Manual preview
YZ65 2021
Бренд: Yamaha Страницы: 86
Yamaha TW200E W 2007 Owner'S Manual preview
TW200E W 2007
Бренд: Yamaha Страницы: 86
Yamaha TT-R50EL 2019 Owner'S Manual preview
TT-R50EL 2019
Бренд: Yamaha Страницы: 86
Yamaha TW200B Owner'S Manual preview
TW200B
Бренд: Yamaha Страницы: 100
Yamaha TT-R50EM Owner'S Manual preview
TT-R50EM
Бренд: Yamaha Страницы: 88
Yamaha YZF-R1L Owner'S Manual preview
YZF-R1L
Бренд: Yamaha Страницы: 119

Бренды по названию

Популярные бренды

Загрузить еще бренды