manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Note

Do not turn the connecting rod and crankshaft during the clearance measurement as this will
damage the Plastigauge. The crankshaft journal clearances are measured using Plastigauge
(Triumph part number 3880150-T0301).

Remove the big end cap from the journal to be checked.

2. 

Wipe the exposed areas of the crankshaft journal, and the bearing face inside the cap.

3.

Apply a thin smear of grease to the journal and a small quantity of silicone release agent to the bearing.

4.

Trim a length of the Plastigauge to fit across the journal. Fit the strip to the journal using the grease to hold
the Plastigauge in place.

5. 

Lubricate the threads of the bolt and the face of the nut with molybdenum disulphide grease. Refit the
bearing end cap and tighten the big end nuts (see Connecting Rods - Installation).

6. 

Release the nuts and remove the cap being measured. Using the gauge provided with the Plastigauge kit,
measure the width of the compressed Plastigauge.

7. 

chdv

Checking the Measured Clearance

For specifications refer toCrankshaft.

8.

Note

If the measured clearance exceeds the service limit, measure the crankshaft journal diameter.
If any crankshaft journal has worn beyond the service limit, the crankshaft must be replaced. Due to
the advanced techniques used during manufacture, the crankshaft cannot be reground and no
oversize bearings are available.

Connecting Rod Bearing Selection

Minor differences in connecting rod dimensions are compensated for by using selective bearings. For further
information on bearing part number to colour cross-references, see the latest parts information.

Select the correct big end bearing shell as follows:

1.

Measure each crankshaft journal diameter
Note the connecting rod marking.
Select the correct bearings by matching the information found with the chart below.

2.

Connecting Rod Bearing Selection Chart (all dimensions in mm)

Shell Colour

White

Red

Red

Blue

Tiger Explorer XR Series

151 of 746

CRANKSHAFT / RODS / PISTONS

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

yasuni R2 Assembly Instructions Manual preview
R2
Бренд: yasuni Страницы: 11
Yamaha YZ125(T)/T1 Owner'S Service Manual preview
YZ125(T)/T1
Бренд: Yamaha Страницы: 568
Suzuki RM85 Owner'S Service Manual preview
RM85
Бренд: Suzuki Страницы: 206
R&G LP0274BK Fitting Instructions Manual preview
LP0274BK
Бренд: R&G Страницы: 24
AC Schnitzer AC S II Fitting Instructions Manual preview
AC S II
Бренд: AC Schnitzer Страницы: 44
Yamaha XS650SE Shop Manual preview
XS650SE
Бренд: Yamaha Страницы: 215
Yamaha XS1100SH Service Manual preview
XS1100SH
Бренд: Yamaha Страницы: 319
Yamaha TMAX 2020 Service Manual preview
TMAX 2020
Бренд: Yamaha Страницы: 688
Yamaha XMAX YP250R 2013 Owner'S Manual preview
XMAX YP250R 2013
Бренд: Yamaha Страницы: 94
hepco & becker 5049529 00 01 Quick Start Manual preview
5049529 00 01
Бренд: hepco & becker Страницы: 4
Yamaha YZF-R1 Assembly Instructions Manual preview
YZF-R1
Бренд: Yamaha Страницы: 15
Yamaha YW50A Owner'S Manual preview
YW50A
Бренд: Yamaha Страницы: 84
Mash Black Seven 250 User Manual preview
Black Seven 250
Бренд: Mash Страницы: 62
Marzocchi Shiver 50 Manual preview
Shiver 50
Бренд: Marzocchi Страницы: 116
HealTech Electronics BLP-U04 Supplementary Manual preview
BLP-U04
Бренд: HealTech Electronics Страницы: 2
Healtech GIpro X-type User Manual preview
GIpro X-type
Бренд: Healtech Страницы: 6
GÜDE 16922 Translation Of The Original Instructions preview
16922
Бренд: GÜDE Страницы: 80
GÜDE 16926 Translation Of The Original Instructions preview
16926
Бренд: GÜDE Страницы: 88

Бренды по названию

Популярные бренды

Загрузить еще бренды