manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Typical Values

In a correctly adapted motorcycle, the following will be typical:

Function Examined

Read Out

Closed throttle position reference status

Adapted

Idle speed control adaption status

B100 and -100%

Oxygen sensor adaption status (off idle)

0% +/- 10%

Oxygen sensor adaption range (off idle)

B100 and -100%

Oxygen sensor adaption status (idle)

0% +/- 10%

Oxygen sensor adaption range (idle)

B100 and -100%

Forcing Adaption to Take Place

If the read out indicates that the motorcycle is not adapted, the following will force the system to make
adaptions:

WARNING

Never start the engine or let it run for any length of time in a closed area. The exhaust fumes are poisonous
and may cause loss of consciousness and death within a short time. Always operate the motorcycle in the
open-air or in an area with adequate ventilation.

Note

Resetting adaptions with the motorcycle connected to an exhaust extraction system may cause
incorrect values to be set, causing poor engine running. Always reset the adaptions with the engine
disconnected from any exhaust extraction system whilst ensuring the motorcycle is positioned in a
well ventilated area.

Ensure the engine is cold.

1.

WITHOUT TOUCHING THE THROTTLE, start the engine and allow it to warm up until the cooling fan
comes on.

2. 

Leave the engine to idle for a further 12 minutes.

3.

Note

As an alternative to the above process, connect the diagnostic tool, select ADJUST TUNE (see the
Triumph Diagnostic Tool User Guide) and select RESET ADAPTIONS. This will force a fast adaption
routine to take place in around five seconds. For this to happen, the engine MUST be running, it
must be at normal operating temperature and in closed loop control mode. Under any other
conditions fast adaption will not take place and may cause default values to be loaded, which may
then require a normal 12 minute adaption routine to be run.

Fault Indications

If 'range' figures at 100% are seen, then the adjustment has reached maximum indicating a mechanical fault
exists on the motorcycle. This can be due to a number of faults but the most likely causes will be low/high fuel
pressure, faulty injectors or air leaks at the throttle bodies or airbox.
In these circumstances, locate and rectify the fault, and reset the adaptions as described above.

Exhaust System - Installation

Tiger Explorer XR Series

333 of 746

FUEL SYSTEM / ENGINE MANAGEMENT

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Razor Indian eFTR Mini 2021 Owner'S Manual preview
Indian eFTR Mini 2021
Бренд: Razor Страницы: 20
hepco & becker 501546 00 01 Manual preview
501546 00 01
Бренд: hepco & becker Страницы: 5
Yamaha RMAX WOLVERINE 2021 Owner'S Manual preview
RMAX WOLVERINE 2021
Бренд: Yamaha Страницы: 192
Yamaha YZ 2015 Series Owner'S Service Manual preview
YZ 2015 Series
Бренд: Yamaha Страницы: 396
Yamaha YXF10WRAN Owner'S Manual preview
YXF10WRAN
Бренд: Yamaha Страницы: 192
Yamaha TMAX ABS Series Owner'S Manual preview
TMAX ABS Series
Бренд: Yamaha Страницы: 122
Yamaha Tenere 700 2024 Owner'S Manual preview
Tenere 700 2024
Бренд: Yamaha Страницы: 110
PMI Ventilator Instructions preview
Ventilator
Бренд: PMI Страницы: 2
Honeywell EV1 User'S Information Manual preview
EV1
Бренд: Honeywell Страницы: 8
Honeywell HW100 Important Instructions & Warnings preview
HW100
Бренд: Honeywell Страницы: 304
Royal Enfield METEOR 350 2021 Owner'S Manual preview
METEOR 350 2021
Бренд: Royal Enfield Страницы: 116
BUMOT Pannier Rack Installation Instructions preview
Pannier Rack
Бренд: BUMOT Страницы: 3
Sealey Siegen Tools S01001.V3 Instructions preview
Siegen Tools S01001.V3
Бренд: Sealey Страницы: 4
Yamaha BWS CW50L Owner'S Manual preview
BWS CW50L
Бренд: Yamaha Страницы: 68
Yamaha QT 50F Service Manual preview
QT 50F
Бренд: Yamaha Страницы: 65
Yamaha PW80(T) Manual preview
PW80(T)
Бренд: Yamaha Страницы: 64
Yamaha NEO'S YN50 Owner'S Manual preview
NEO'S YN50
Бренд: Yamaha Страницы: 72
Yamaha Nmax 125-A Owner'S Manual preview
Nmax 125-A
Бренд: Yamaha Страницы: 90

Бренды по названию

Популярные бренды

Загрузить еще бренды