manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Holding the inner and outer tubes together, invert the fork and pour out the fork oil into a suitable container.

5. 

Return the fork to the fork holding tool.

6.

Counterhold the top cap to prevent it from turning and loosen the top cap lock nut.

7.

Remove the top cap.

8.

Fit a suitable ring spanner over the spring guide and seat it onto the taper section of the spring guide.

9.

WARNING

While compressing the fork spring always wear protective equipment for the face and eyes and never look
directly down on the fork. If the spring compressor should dislodge or detach, the resulting release of spring
tension could cause parts to fly off resulting in injury to the user.

While supporting the fork inner tube, press down on the spanner to compress the spring and remove the nut
and washer.

10. 

Remove the spanner used to compress the spring.

11.

Note

Between the spring and the spring guide there could be one or more spacers fitted.

Remove the spring guide, collecting the spring preload spacer(s) as you do so.

12.

1

3

2

4

5

Spring

1.

Spring guide

2.

Spring preload spacer(s)

3.

Nut and washer

4.

Spanner

5.

Remove the spring.

13.

Remove the fork from the fork holding tool.

14.

Note

Ensure that the inner damping rod is retained in position when inverting the fork assembly.

Holding the inner and outer tubes together, invert the fork and pour out any remaining fork oil into a suitable
container. Pump the damper rod to remove all the oil.

15. 

Ensuring that the inner damping rod is retained, invert the fork and return it to the fork holding tool.

16.

Raise the inner tube and remove the dust seal from the outer tube.

17.

Tiger Explorer XR Series

380 of 746

FRONT SUSPENSION

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

DMC 25470-00 Installation Instructions preview
25470-00
Бренд: DMC Страницы: 2
R&G FI0001BK Fitting Instructions preview
FI0001BK
Бренд: R&G Страницы: 3
S&S Cycle Stealth Air Cleaner Kit Installation Instructions preview
Stealth Air Cleaner Kit
Бренд: S&S Cycle Страницы: 4
Ducati MONSTER 400 Owner'S Manual preview
MONSTER 400
Бренд: Ducati Страницы: 77
KTM F9903SE Setup Instructions preview
F9903SE
Бренд: KTM Страницы: 25
Leatt 4.0 DBX Manual preview
4.0 DBX
Бренд: Leatt Страницы: 23
Bosch GHJ 10,8+18V Unisex Original Instructions Manual preview
GHJ 10,8+18V Unisex
Бренд: Bosch Страницы: 14
Bosch LTE65 Manual preview
LTE65
Бренд: Bosch Страницы: 28
Bosch 06188000DY Original Instructions Manual preview
06188000DY
Бренд: Bosch Страницы: 145
Arai QUANTUM-X Operation Instructions Manual preview
QUANTUM-X
Бренд: Arai Страницы: 12
Innovv C5 User Manual preview
C5
Бренд: Innovv Страницы: 2
RIDLEY Motorcycles 2006 Owner'S Manual preview
Motorcycles 2006
Бренд: RIDLEY Страницы: 53
MARTINDALE M23AWH 9/13 User Instructions preview
M23AWH 9/13
Бренд: MARTINDALE Страницы: 39
Kinroad XT50GY User Manual preview
XT50GY
Бренд: Kinroad Страницы: 28
Petzl A073AA00 Technical Notice preview
A073AA00
Бренд: Petzl Страницы: 12
Beta Minicross R 10 Service Manual preview
Minicross R 10
Бренд: Beta Страницы: 41
KTM 61508908000 Fitting Instructions Manual preview
61508908000
Бренд: KTM Страницы: 52
KTM 79635965044 Fitting Instructions Manual preview
79635965044
Бренд: KTM Страницы: 72

Бренды по названию

Популярные бренды

Загрузить еще бренды