manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

WARNING

∙Alternator rotor
∙Magnetic fuel tank bags
∙Audio speakers
∙Magnetic dial test indicator stand
∙Magnetic parts tray.
If the ABS is not functioning, the brake system will continue to function as a non-ABS braking system. Do not
continue to ride for longer than is necessary with the indicator light illuminated. Ride with extreme caution
when performing diagnostic troubleshooting on a non-functioning ABS system. In this situation braking too
hard will cause the wheels to lock resulting in loss of motorcycle control and an accident.

Front Brake Fluid Level Inspection

Rear Brake Fluid Level Inspection

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

In accordance with the scheduled maintenance chart, inspect the brake fluid level in the front and rear master
cylinder reservoirs.

To inspect the fluid level, check the level of fluid visible in the window at the front of the reservoir body.

1. 

2

kabi_1

1

Front reservoir upper level

1.

Front reservoir lower level

2.

Ensure that the brake fluid level in the front brake fluid reservoir is between the upper and lower level lines
(reservoir held horizontal).

2. 

To adjust the fluid level:

3.

Remove the two fixings.
Remove the reservoir cap and the diaphragm seal.
Fill the reservoir to the upper level line using new DOT 4 fluid from a sealed container.
Refit the reservoir cap, ensuring that the diaphragm seal is correctly positioned between the cap and
reservoir body.
Refit the two fixings and tighten to 

1.5 Nm

.

Tiger Explorer XR Series

459 of 746

BRAKES

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Keis X900 Operating Instructions preview
X900
Бренд: Keis Страницы: 2
Razor Indian eFTR Mini 2021 Owner'S Manual preview
Indian eFTR Mini 2021
Бренд: Razor Страницы: 20
Öhlins McPherson Strut MIR 1G00 Mounting Instructions preview
McPherson Strut MIR 1G00
Бренд: Öhlins Страницы: 2
Öhlins BM 543 Mounting Instruction preview
BM 543
Бренд: Öhlins Страницы: 2
Öhlins BM 503 Mounting Instructions preview
BM 503
Бренд: Öhlins Страницы: 2
SCORPION Exo-R410 Technical Manual preview
Exo-R410
Бренд: SCORPION Страницы: 12
GIVI SR6110 Quick Start Manual preview
SR6110
Бренд: GIVI Страницы: 3
R&G BRG0013 Fitting Instructions Manual preview
BRG0013
Бренд: R&G Страницы: 9
GAS GAS 2003 FSE Parts List preview
2003 FSE
Бренд: GAS GAS Страницы: 26
Pacific Helmets HALOFLEX F20H User'S Information Manual preview
HALOFLEX F20H
Бренд: Pacific Helmets Страницы: 40
Yamaha YZ65 2021 Manual preview
YZ65 2021
Бренд: Yamaha Страницы: 86
Yamaha TW200E W 2007 Owner'S Manual preview
TW200E W 2007
Бренд: Yamaha Страницы: 86
Yamaha TT-R50EL 2019 Owner'S Manual preview
TT-R50EL 2019
Бренд: Yamaha Страницы: 86
Yamaha TW200B Owner'S Manual preview
TW200B
Бренд: Yamaha Страницы: 100
Yamaha TT-R50EM Owner'S Manual preview
TT-R50EM
Бренд: Yamaha Страницы: 88
Yamaha YZF-R1L Owner'S Manual preview
YZF-R1L
Бренд: Yamaha Страницы: 119
Yamaha MIO AL115S 2010 Owner'S Manual preview
MIO AL115S 2010
Бренд: Yamaha Страницы: 80
Yamaha MT09 2020 Owner'S Manual preview
MT09 2020
Бренд: Yamaha Страницы: 112

Бренды по названию

Популярные бренды

Загрузить еще бренды