manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Balancer

The balancer is fitted to control 'pulsing' within the engine. Without any form of balancer, the engine would
'pulse' each time the crankshaft rotated. This 'pulsing' would be felt as a vibration which would amplify as the
engine speed was increased.
The balancer has the effect of a pair of counterbalance weights which create an equal amount of energy in the
opposite direction, and at the same time as that produced by the crankshaft, pistons and connecting rods.
Because the opposing pulses occur at the same point of crankshaft rotation, and are of an equal magnitude, a
state of equilibrium or balance is reached.

Balancer - Removal

Separate the crankcase halves (see Crankcases - Disassembly).
With the crankcase halves separated, lift out the balancer shaft complete with the shaft bearings/circlips.

1. 

To remove the left hand bearing, slide the bearing, circlip and bearing sleeve from the balancer shaft.

2.

To remove the right hand bearing, remove the circlip and slide the bearing race and thrust washer from the
shaft.

3. 

Balancer - Inspection

Inspect all gears for chipped or missing teeth.

1.

Inspect all bearings for signs of overheating (blue discolouration), seized or damaged rollers, and any other
damage.

2. 

Inspect the gear teeth for overheating (blue discolouration).

3.

Note

Signs of blue discolouration on the gear centre are due to the manufacturing process and must be
disregarded.

Balancer - Installation

Lubricate and fit the right hand bearing and circlip to the shaft.

1.

Lubricate and fit the left hand bearing and circlip.

2.

Locate the balancer to the crankcase aligning the balancer gears and crankshaft as shown in the illustration
below, while ensuring that the bearing circlips and pins locate correctly in their corresponding grooves in the
crankcase.

3. 

Tiger Explorer XR Series

164 of 746

BALANCER 

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

R&G FI0054BK Fitting Instructions preview
FI0054BK
Бренд: R&G Страницы: 4
Triumph Sprint RS Service Manual preview
Sprint RS
Бренд: Triumph Страницы: 410
Suzuki 1987 GSX-R150 Service Manual preview
1987 GSX-R150
Бренд: Suzuki Страницы: 311
X-lite X-402 T Safety And Instructions For Use preview
X-402 T
Бренд: X-lite Страницы: 96
Nolan N60-5 Safety And Instructions For Use preview
N60-5
Бренд: Nolan Страницы: 80
Bajaj Pulsar 135 BS VI Owner'S Manual preview
Pulsar 135 BS VI
Бренд: Bajaj Страницы: 48
PUIG 21226 Mounting Instructions preview
21226
Бренд: PUIG Страницы: 6
BMW HP2 ENDURO Manual preview
HP2 ENDURO
Бренд: BMW Страницы: 139
Isotta SP8106 R1200R Fitting Instructions preview
SP8106 R1200R
Бренд: Isotta Страницы: 2
GAS GAS TXT ROOKIE - 2006 Service Manual preview
TXT ROOKIE - 2006
Бренд: GAS GAS Страницы: 32
KTM 690 SMC R 2016 Series Setup Instructions preview
690 SMC R 2016 Series
Бренд: KTM Страницы: 18
Yamaha XSR700M 2021 Owner'S Manual preview
XSR700M 2021
Бренд: Yamaha Страницы: 104
Yamaha Super Tenere ABS 2018 Owner'S Manual preview
Super Tenere ABS 2018
Бренд: Yamaha Страницы: 122
Yamaha XSR900P Owner'S Manual preview
XSR900P
Бренд: Yamaha Страницы: 124
Yamaha XTZ 125K Owner'S Manual preview
XTZ 125K
Бренд: Yamaha Страницы: 97
Öhlins BM 701 Mounting Instructions preview
BM 701
Бренд: Öhlins Страницы: 2
Serpento COYOTE 250 User Manual/Maintenance preview
COYOTE 250
Бренд: Serpento Страницы: 66
EINHELL BG-SH 1 Original Operating Instructions preview
BG-SH 1
Бренд: EINHELL Страницы: 48

Бренды по названию

Популярные бренды

Загрузить еще бренды