manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

WARNING

The clutch switch is an integral part of the cruise control system. To ensure the clutch switch functions
correctly after a replacement, the cruise control switch test must be carried out (see Cruise Control Switch
Check).
Failure to carry out the cruise control switch check may result in loss of motorcycle control and an accident.

The clutch switch is an integral part of the left hand switch cube. If the clutch switch requires replacement, the
left hand switch cube and clutch switch assembly must be replaced.

Clutch Fluid Level Inspection

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

In accordance with the scheduled maintenance chart, inspect the clutch fluid level in the master cylinder
reservoir.

Ensure that the clutch fluid level in the clutch fluid reservoir is between the upper and lower level lines
(reservoir held horizontal).

1. 

5

1

1

2

3

4

chgv

Fixings

1.

Cover

2.

Diaphragm seal

3.

Upper level line

4.

Lower level line

5.

To inspect the fluid level, check the level of fluid visible in the window at the front of the reservoir body.

2.

To adjust the fluid level:

3.

Release the fixings and detach the cover noting the position of the sealing diaphragm.
Fill the reservoir to the upper level line using new DOT 4 brake and clutch fluid from a sealed container.
Refit the cover, ensuring that the diaphragm seal is correctly positioned between the cover and reservoir
body. Secure with the fixings and tighten to 

1.5 Nm

.

Bleeding the Clutch

Note the original setting of the clutch lever adjuster in order that it can be returned to the same position
when the bleeding operation is complete. Set the clutch lever adjuster to position No. 1.

1. 

Tiger Explorer XR Series

115 of 746

CLUTCH

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

kellermann Atto Integral Installation Manual preview
Atto Integral
Бренд: kellermann Страницы: 2
R&G BRG0004BK Fitting Instructions Manual preview
BRG0004BK
Бренд: R&G Страницы: 12
R&G CR0076BK Fitting Instructions Manual preview
CR0076BK
Бренд: R&G Страницы: 9
Suzuki Intruder VS700 Service Manual preview
Intruder VS700
Бренд: Suzuki Страницы: 526
Cake Kalk Manual preview
Kalk
Бренд: Cake Страницы: 12
Honda CBF190WH 2016 Shop Manual preview
CBF190WH 2016
Бренд: Honda Страницы: 130
thousand TRAVELER LIGHT Owner'S Manual preview
TRAVELER LIGHT
Бренд: thousand Страницы: 32
Honda 1999 Shadow Aero VT1100C3 Owner'S Manual preview
1999 Shadow Aero VT1100C3
Бренд: Honda Страницы: 226
APRILIA SCARABEO 100 4T - 06-2001 PART6 Manual preview
SCARABEO 100 4T - 06-2001 PART6
Бренд: APRILIA Страницы: 6
Yamaha YZ125 2016 Owner'S Service Manual preview
YZ125 2016
Бренд: Yamaha Страницы: 166
Yamaha YZ125 2015 Owner'S Service Manual preview
YZ125 2015
Бренд: Yamaha Страницы: 166
Yamaha YZ250F(D) Owner'S Service Manual preview
YZ250F(D)
Бренд: Yamaha Страницы: 198
Yamaha YZ250 2022 Owner'S Service Manual preview
YZ250 2022
Бренд: Yamaha Страницы: 274
Yamaha YZ250F(E) Owner'S Service Manual preview
YZ250F(E)
Бренд: Yamaha Страницы: 356
Yamaha YZ 2020 Series Owner'S Service Manual preview
YZ 2020 Series
Бренд: Yamaha Страницы: 376
Yamaha YZ125(P)/LC Owner'S Service Manual preview
YZ125(P)/LC
Бренд: Yamaha Страницы: 564
Yamaha YZ 2016 Series Owner'S Service Manual preview
YZ 2016 Series
Бренд: Yamaha Страницы: 392
Yamaha YZ 2018 Series Owner'S Service Manual preview
YZ 2018 Series
Бренд: Yamaha Страницы: 402

Бренды по названию

Популярные бренды

Загрузить еще бренды