manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Refit the sump, ensuring the water pump drain tube is correctly installed (see Sump - Installation).

5. 

Refill the engine with oil (see Oil and Oil Filter Change).

6.

Reconnect the battery, positive (red) lead first.

7.

Start the engine and check for oil leaks. Once a leak check has been made, stop the engine and allow to
stand for 10 minutes.

8. 

Adjust the engine oil level (see Oil Level Inspection).

9.

Refit the rider’s seat (see Rider’s Seat - Installation).

10.

Engine Removal and Installation

 

Engine - Removal

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

Raise and securely support the motorcycle.
Remove the rider’s seat (see Rider’s Seat - Removal).
Remove the battery (see Battery Removal).
Remove the engine bars (see Engine Bars - Removal).
Remove the fuel tank (see Fuel Tank - Removal).
Remove the airbox (see Airbox - Removal).
Remove the throttle bodies (see Throttle Bodies/Injectors - Removal).
Drain the engine oil (see Oil and Oil Filter Change).
Remove the radiator (see Radiator - Removal).
Remove the radiator mounting brackets from the engine.
Remove the exhaust system (see Exhaust System - Removal).
Remove the rear bevel box (see Rear Bevel Box - Removal).
Remove the coolant expansion tank (see Expansion Tank - Removal).

Note

Secure the coolant hoses to prevent damage as the engine is removed.

Drain the clutch fluid and detach the clutch hose from the master cylinder (see Clutch Master Cylinder -
Removal).

1. 

Detach the rear brake line and its bracket from the crankcase tidy moulding.

2.

1

4

3

2

chmb

Tiger Explorer XR Series

216 of 746

ENGINE REMOVAL / INSTALLATION

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

GAS GAS MC50 2021 Owner'S Manual preview
MC50 2021
Бренд: GAS GAS Страницы: 119
PZRacing GearTronic ZERO GT3100-K1 User Manual preview
GearTronic ZERO GT3100-K1
Бренд: PZRacing Страницы: 2
Yamaha TZ250M1 Owner'S Service Manual preview
TZ250M1
Бренд: Yamaha Страницы: 287
Yamaha TW200P Owner'S Manual preview
TW200P
Бренд: Yamaha Страницы: 109
GAS GAS EX 250 2023 Owner'S Manual preview
EX 250 2023
Бренд: GAS GAS Страницы: 144
Shark SHKC7800N User Manual preview
SHKC7800N
Бренд: Shark Страницы: 16
R&G FI0087BK Fitting Instructions preview
FI0087BK
Бренд: R&G Страницы: 2
R&G FP0225BK Fitting Instructions Manual preview
FP0225BK
Бренд: R&G Страницы: 9
R&G FI0076BK Fitting Instructions preview
FI0076BK
Бренд: R&G Страницы: 4
R&G FI0081BK Fitting Instructions Manual preview
FI0081BK
Бренд: R&G Страницы: 6
Kuberg CROSS Owner'S Manual preview
CROSS
Бренд: Kuberg Страницы: 16
Kuberg Freerider 2016 Owner'S Manual preview
Freerider 2016
Бренд: Kuberg Страницы: 32
Malaguti XSM 50 Workshop Manual preview
XSM 50
Бренд: Malaguti Страницы: 42
Malaguti CNK 50 DRAKON Workshop Manual preview
CNK 50 DRAKON
Бренд: Malaguti Страницы: 80
Denali DialDim Instruction Manual preview
DialDim
Бренд: Denali Страницы: 3
Benelli TnT1130 Workshop Manual preview
TnT1130
Бренд: Benelli Страницы: 392
APRILIA Mana GT ABS 2012 Manual preview
Mana GT ABS 2012
Бренд: APRILIA Страницы: 148
APRILIA Habana 125 Manual preview
Habana 125
Бренд: APRILIA Страницы: 104

Бренды по названию

Популярные бренды

Загрузить еще бренды