Triumph Tiger Explorer XR 2016 Скачать руководство пользователя | Manualshive

Страница: 152 / 750

background image

Refit the clutch (see Clutch - Installation).
Refit the flywheel cover (see Flywheel Cover - Installation).
Refit the crankshaft cover (see Crankshaft Cover - Installation).
Refit the balancer shaft cover (see Balancer Shaft Cover - Installation).
Refit the sump (see Sump - Installation).
Install the engine in the frame (see Engine - Installation).

Connecting Rods - Installation

Remove the engine from the frame (see Engine - Removal).
Remove the cylinder head (see Cylinder Head - Removal).
Remove the cylinder liners (see Cylinder Liners - Removal).
Remove the pistons from the connecting rod (see Pistons - Disassembly).
Separate the two halves of the crankcase (see Crankcases - Disassembly).
Mark each big end cap and connecting rod to identify both items as a matched pair and to identify the
correct orientation of the bearing cap to the connecting rod.

1.

Release and discard the connecting rod nuts and remove the big end cap. Ensure that the bearing shell
remains in place in the cap.

2.

2

1

chdu

Big end cap

1.

Connecting rod nuts

2.

Note

It may be necessary to gently tap the big end cap with a rubber mallet to release the cap from the
bolts.

Push the connecting rod up through the crankcase and collect the connecting rod from the top.

3.

Label the assembly to identify the cylinder from which it was removed.

4.

Remove and discard the connecting rod bolts.

5.

CAUTION

Never reuse connecting rod bolts or nuts. If the connecting rod cap is disturbed, always renew the bolts and
nuts. Using the original bolts and nuts may lead to severe engine damage.

Connecting Rod Bearing Selection/ Crankshaft Journal Wear Check

Crankshaft - Removal

Tiger Explorer XR Series

148 of 746

CRANKSHAFT / RODS / PISTONS

«
...
150
151
152
153
154
...
»

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Бренд: R&G Страницы: 12

Бренд: Suzuki Страницы: 59

Бренд: Sachs Bikes Страницы: 71

Turismo Veloce 800 LUSSO

Бренд: AGUSTA Страницы: 616

Бренд: R&G Страницы: 24

Бренд: J&M Страницы: 5

65175810022-00-40

Бренд: hepco & becker Страницы: 4

Бренд: RDMOTO Страницы: 2

Firstgear 512817

Бренд: Dennis Kirk Страницы: 2

Daytona 675 2014

Бренд: Triumph Страницы: 162

Бренд: Isotta Страницы: 2

Бренд: TVS Страницы: 60

Бренд: Baja motorsports Страницы: 66

STAR XV19CSX(C)

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 102

Бренд: Yamaha Страницы: 100

Star XV250B 2011

Бренд: Yamaha Страницы: 98

Бренд: Malossi Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды