manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Raise the rear of the fuel tank and carefully slide the fuel tank rearwards to release its front mountings.
Place the fuel tank onto a clean flat surface ensuring that the spigots and their caps do not make contact
with the flat surface.

19. 

CAUTION

When the fuel tank has been removed from the motorcycle, the fuel clamps must be removed from the
transfer pipe and the fuel drained into a suitable fuel container.
Keeping the fuel clamps on the transfer pipe for long periods of time may deform the fuel transfer pipe.

Remove the fuel line clamps from the transfer pipe and drain any fuel into an approved fuel container.

20. 

Fuel Tank - Installation

Note

Due to the shape of the fuel tank, a small amount of fuel may remain in the fuel tank after draining.

Prior to fitting the fuel tank, drain any remaining fuel that may be in the fuel tank using proprietary
professional automotive workshop equipment approved for fuel handling.

1. 

Refit the fuel line clamps to the three ends of the fuel transfer pipe.

2.

Align the three front mountings on the fuel tank to their rubber mountings on the frame and push forward
until fully engaged.

3. 

chka_1

1

Front mountings

1.

Remove the blanking cap from one of the front spigots. At the same time, refit the front fuel transfer pipe to
the spigot and secure with its clip.

4. 

Repeat step 4 for the other front fuel transfer pipe.

5.

Remove the fuel line clamps from the two front transfer pipes.

6.

Pivot the fuel tank upwards at the rear and carry out the following:

7.

Remove the blanking cap from the rear spigot. At the same time, refit the rear fuel transfer pipe to the spigot
and secure with its clip.
Remove the fuel line clamp from the rear fuel transfer pipe.
Route the drain hose as noted for removal and secure it to its retaining clips on the rider’s seat front
mounting.
Fit the two breather pipes as noted for removal.
Fit the fuel pump and fuel level sensor electrical connectors.
Reconnect the fuel feed hose by gently pushing inwards until the hose engages with a click.
Slide the double check-latch down (i.e. towards the spigot) until the release buttons of the fuel connector are
covered. If the latch will not slide into position, then the fuel hose is not fully home on its spigot and must

8. 

Tiger Explorer XR Series

305 of 746

FUEL SYSTEM / ENGINE MANAGEMENT

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Cake Makka Quick Start Manual preview
Makka
Бренд: Cake Страницы: 13
Öhlins McPherson Strut MIR 1G00 Mounting Instructions preview
McPherson Strut MIR 1G00
Бренд: Öhlins Страницы: 2
Öhlins BM 543 Mounting Instruction preview
BM 543
Бренд: Öhlins Страницы: 2
Öhlins BM 503 Mounting Instructions preview
BM 503
Бренд: Öhlins Страницы: 2
Öhlins YA919 Mounting Instructions preview
YA919
Бренд: Öhlins Страницы: 2
SUOMY C1SF0001 Instructions For User preview
C1SF0001
Бренд: SUOMY Страницы: 84
Takegawa 02-01-0284 Instruction Manual preview
02-01-0284
Бренд: Takegawa Страницы: 2
Memphis Shades 2320-0032 Mounting Instructions preview
2320-0032
Бренд: Memphis Shades Страницы: 2
Razor Crazy Cart XL Replacement Instructions preview
Crazy Cart XL
Бренд: Razor Страницы: 3
Dayi Motor E-ODIN 2.0 Instructions Manual preview
E-ODIN 2.0
Бренд: Dayi Motor Страницы: 18
Pagsta BOBBER User Manual preview
BOBBER
Бренд: Pagsta Страницы: 47
Yamaha QT50 Owner'S Manual preview
QT50
Бренд: Yamaha Страницы: 39
Yamaha Roadliner XV1900AV Owner'S Manual preview
Roadliner XV1900AV
Бренд: Yamaha Страницы: 86
Yamaha ROADLINER XV19C Owner'S Manual preview
ROADLINER XV19C
Бренд: Yamaha Страницы: 95
Yamaha PW80(Y) Owner'S Manual preview
PW80(Y)
Бренд: Yamaha Страницы: 70
Yamaha Road Star XV1600AT 2004 Owner'S Manual preview
Road Star XV1600AT 2004
Бренд: Yamaha Страницы: 84
Yamaha PW80(Z) Owner'S Manual preview
PW80(Z)
Бренд: Yamaha Страницы: 72
Yamaha PW80(W) Owner'S Manual preview
PW80(W)
Бренд: Yamaha Страницы: 72

Бренды по названию

Популярные бренды

Загрузить еще бренды