manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Disconnect the Triumph Diagnostic Tool.

10.

Refit the rider’s seat (see Rider’s Seat - Installation).

11.

Swinging Arm - Inspection

The Rear Preload Motor Up/Down function tests provided in the Triumph Diagnostic Tool may be used as
follows:

Test rear preload motor operation.
Free the rear preload motor if it is stuck at an end stop.

Test Rear Preload Motor Operation

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

Connect the Triumph diagnostic tool and switch the ignition on.

1.

Navigate to CHASSIS DIAGNOSTICS - CHASSIS ECM DIAGNOSTICS and select FUNCTION TESTS.

2.

CAUTION

If the rear preload motor adjustment position reaches its maximum or minimum adjustment end stop, do not
continue to drive the motor towards the end stop.
Select the test direction that will drive motor away from the end stop as described later in this procedure.
Repeatedly driving the rear preload motor against an end stop may cause the motor to overheat, which can
result in permanent damage.

Note

The position of the rear preload motor adjustment can be checked visually as follows:
At the maximum preload end stop, the preload adjustment collar is fully extended from the base of
the motor housing. Approximately 20 mm of the adjustment collar is visible as shown below.
At intermediate preload adjustment positions, less of the adjustment collar will be visible as the
adjustment position moves closer to the minimum preload end stop.
At the minimum preload end stop, the preload adjustment collar is fully retracted into the motor
housing.

Rear preload motor housing

1.

Adjustment collar (maximum preload position -
fully extended)

2. 

Adjustment collar (minimum preload position -
fully retracted)

3. 

Visually Check the position of the rear preload motor.

3.

Note

If the rear preload motor is positioned at or near the minimum or maximum adjustment end stop, the

Tiger Explorer XR Series

419 of 746

REAR SUSPENSION

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

3M Versaflo M Series User Instructions preview
Versaflo M Series
Бренд: 3M Страницы: 27
3M Speedglas 9100 Series Quick Start Manual preview
Speedglas 9100 Series
Бренд: 3M Страницы: 2
3M L-905 Disassembly preview
L-905
Бренд: 3M Страницы: 5
Parkside PSHL 2 B1 Operation And Safety Notes Translation Of The Original Instructions preview
PSHL 2 B1
Бренд: Parkside Страницы: 89
Parkside PSH 3 A1 Assembly, Operating And Safety Instructions preview
PSH 3 A1
Бренд: Parkside Страницы: 28
BMW R 1200 C Repair Manual preview
R 1200 C
Бренд: BMW Страницы: 288
oset 12.5 Eco Owner'S Manual preview
12.5 Eco
Бренд: oset Страницы: 20
SW-Motech ALK.00.733.15000/B Mounting Instructions preview
ALK.00.733.15000/B
Бренд: SW-Motech Страницы: 14
Coleman Powersports CT200U Owner'S Manual preview
Powersports CT200U
Бренд: Coleman Страницы: 37
BMW Motorrad F 900 XR Rider'S Manual preview
F 900 XR
Бренд: BMW Motorrad Страницы: 261
Mash Two Fifty 250 cc User Manual preview
Two Fifty 250 cc
Бренд: Mash Страницы: 62
Triumph Bonneville T100 Owner'S Handbook Manual preview
Bonneville T100
Бренд: Triumph Страницы: 198
ALPENHEAT fire PANTLINER AJ6 Manual preview
fire PANTLINER AJ6
Бренд: ALPENHEAT Страницы: 26
X-lite LIX9U0003740299 Safety And Instructions For Use preview
LIX9U0003740299
Бренд: X-lite Страницы: 116
Suzuki GSX-R600 Manual preview
GSX-R600
Бренд: Suzuki Страницы: 165
VStreamT Windscreen N20012A Installation And Owner'S Manual preview
Windscreen N20012A
Бренд: VStreamT Страницы: 3
Kenwood KCA-HX7C Instruction Manual preview
KCA-HX7C
Бренд: Kenwood Страницы: 36
Kenwood KCA-HX5M Instruction Manual preview
KCA-HX5M
Бренд: Kenwood Страницы: 97

Бренды по названию

Популярные бренды

Загрузить еще бренды