manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

ccom

Typical Tyre Marking

WARNING

Tyres that have been used on a rolling road dynamometer may become damaged. In some cases, the
damage may not be visible on the external surface of the tyre.
Tyres must be replaced after such use as continued use of a damaged tyre may lead to instability, loss of
control and an accident.

Tyre Pressures

Correct inflation pressure will provide maximum stability, rider comfort and tyre life.
Always check tyre pressures before riding when the tyres are cold. Check tyre pressures daily and adjust if
necessary.
For details of the correct tyre inflation pressures (see Wheels and Tyres).

WARNING

Incorrect tyre inflation will cause abnormal tread wear and instability problems which may lead to loss of
control and an accident.
Under-inflation may result in the tyre slipping on, or coming off the rim. Over-inflation will cause instability
and accelerated tread wear.
Both conditions are dangerous as they may cause loss of control leading to an accident.

Tyre Wear/Wheel Inspection

As the tyre tread wears down, the tyre becomes more susceptible to puncture and failure. It is estimated that
90% of all tyre failures occur during the last 10% of tread life (90% worn). It is false economy and unsafe to use
tyres until they are worn to their minimum.
All tyres are fitted with tread wear indicators. When the tyre becomes worn down as far as the top of a tread
wear indicator, the tyre is worn beyond its service life and must be replaced.

Tiger Explorer XR Series

546 of 746

WHEELS / TYRES

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Yamaha FZ6-SS Service Manual preview
FZ6-SS
Бренд: Yamaha Страницы: 435
Ducati MONSTER 1100 Owner'S Manual preview
MONSTER 1100
Бренд: Ducati Страницы: 128
Memphis Shades 2320-0076 Mounting Instructions preview
2320-0076
Бренд: Memphis Shades Страницы: 2
Sinnis motorcycles TERRAIN 125 Owner'S Manual preview
TERRAIN 125
Бренд: Sinnis motorcycles Страницы: 68
MW TOOLS 829000042 Manual preview
829000042
Бренд: MW TOOLS Страницы: 9
Wunderlich 35520-002 Manual preview
35520-002
Бренд: Wunderlich Страницы: 2
URAL Motorcycles cT 2022 Owner'S Manual preview
cT 2022
Бренд: URAL Motorcycles Страницы: 104
Can-Am Spyder RT Operator'S Manual preview
Spyder RT
Бренд: Can-Am Страницы: 195
Wunderlich F 850 GS Manual preview
F 850 GS
Бренд: Wunderlich Страницы: 6
Peugeot Motorcycles XR6 Workshop Manual preview
XR6
Бренд: Peugeot Motorcycles Страницы: 50
Enerwatt EWB-MOTOM3-BK User Manual preview
EWB-MOTOM3-BK
Бренд: Enerwatt Страницы: 26
LSK FuelGaugePro2 User Manual preview
FuelGaugePro2
Бренд: LSK Страницы: 18
Malaguti XSM 50 Workshop Manual preview
XSM 50
Бренд: Malaguti Страницы: 42
Malaguti CNK 50 DRAKON Workshop Manual preview
CNK 50 DRAKON
Бренд: Malaguti Страницы: 80
APRILIA DORSODURO 750 ABS Manual preview
DORSODURO 750 ABS
Бренд: APRILIA Страницы: 251
Denali DialDim DNL.WHS.22800 Instruction Manual preview
DialDim DNL.WHS.22800
Бренд: Denali Страницы: 3
Peg-Perego DUCATI IGCS0703 Use And Care Manual preview
DUCATI IGCS0703
Бренд: Peg-Perego Страницы: 24
hepco & becker 6617569 01 01 Manual preview
6617569 01 01
Бренд: hepco & becker Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды