manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

1

chgy

Oil drain plug

1.

Oil filter

2.

Unscrew and remove the oil filter using T3880313 - Oil Filter Wrench.

4.

Dispose of the old oil filter in an environmentally friendly way.

5.

Pre-fill a new oil filter with clean engine oil.

6.

Apply a smear of clean engine oil to the sealing ring of the new oil filter.

7.

Fit the oil filter and tighten to 

10 Nm

.

8.

After the oil has completely drained out, fit a new sealing washer to the drain plug. Fit and tighten the plug to

25 Nm

.

9. 

Fill the engine with new oil of the type and grade listed previously and in the specification section.

10.

Start the engine and allow to idle.

11.

CAUTION

Racing the engine before the oil reaches every part can cause engine damage or seizure.

Ensure that the oil pressure warning light extinguishes shortly after starting and the message WARNING -
OIL PRESSURE LOW is not shown in the instrument display screen.

12. 

CAUTION

If the engine oil pressure is too low, the low oil pressure warning light will illuminate. If this light stays on
when the engine is running, stop the engine immediately and investigate the cause. Running the engine with
low oil pressure will cause engine damage.

Stop the engine and check the oil level. Adjust if necessary.

13.

Low Oil Pressure Warning Light Switch - Removal

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

Note

The low oil pressure warning light switch is located in the upper crankcase, behind the cylinder
head.

Remove the rider’s seat (see Rider’s Seat - Removal).
Disconnect the battery, negative (black) lead first.
Remove the throttle bodies (see Throttle Bodies/Injectors - Removal).
Remove the alternator (see Alternator - Removal).
Disconnect the electrical connection to the switch.

1.

Remove the switch and collect the copper washer.

2.

Tiger Explorer XR Series

207 of 746

LUBRICATION

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Cannondale E440 Owner'S Manual preview
E440
Бренд: Cannondale Страницы: 102
KAYO MOTOR K4 Service Manual preview
K4
Бренд: KAYO MOTOR Страницы: 74
KAYO MOTO K4 Assembly Manual preview
K4
Бренд: KAYO MOTO Страницы: 5
Dowco Fastrax 50144-00 Installation Instructions preview
Fastrax 50144-00
Бренд: Dowco Страницы: 3
GAS GAS EC-SIX DAYS - PART LIST 2011 Parts List preview
EC-SIX DAYS - PART LIST 2011
Бренд: GAS GAS Страницы: 6
MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual preview
Stelvio 1200 MY11 2011
Бренд: MOTO GUZZI Страницы: 385
PIAGGIO Liberty 50 Catalyzed 2019 Manual preview
Liberty 50 Catalyzed 2019
Бренд: PIAGGIO Страницы: 62
GAS GAS 2003 FSE Parts List preview
2003 FSE
Бренд: GAS GAS Страницы: 26
Yamaha FJ-09 2014 Owner'S Manual preview
FJ-09 2014
Бренд: Yamaha Страницы: 126
Pacific Helmets HALOFLEX F20H User'S Information Manual preview
HALOFLEX F20H
Бренд: Pacific Helmets Страницы: 40
JIMS 25254-93A Instruction Sheet preview
25254-93A
Бренд: JIMS Страницы: 2
Gemini 953 Installation And Use Manual preview
953
Бренд: Gemini Страницы: 20
Gemini 953NH User'S And Installer'S Manual preview
953NH
Бренд: Gemini Страницы: 17
X-PRO XB27B-125 Manual preview
XB27B-125
Бренд: X-PRO Страницы: 3
X-PRO Marvel A09 Quick Manual preview
Marvel A09
Бренд: X-PRO Страницы: 3
RIEJU MRX-SMX 50 Chassis Workshop Manual preview
MRX-SMX 50
Бренд: RIEJU Страницы: 52
Benelli TNT 115 User Manual preview
TNT 115
Бренд: Benelli Страницы: 47
Benelli Tornado Naked Tre 1130 Owner'S Manual preview
Tornado Naked Tre 1130
Бренд: Benelli Страницы: 55

Бренды по названию

Популярные бренды

Загрузить еще бренды