manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Do not allow oil or grease to enter blind threaded holes. The hydraulic action on screwing in the bolt or stud
could split the housing.
Always tighten a nut or bolt to the recommended torque figure. Damaged or corroded threads can affect the
torque reading.
Unless specified, threaded fixings must always be fitted dry (no lubrication).

WARNING

Never lubricate a thread unless instructed to do so.
When a thread of a fixing is lubricated, the thread friction is reduced. When the fixing is tightened, reduced
friction will cause over tightening and possible fixing failure.
A fixing which fails in service could cause component detachment leading to loss of control and an accident.

Locking Devices

Always release locking tabs and fit new locking washers. Do not reuse locking tabs.

Fitting a Split Pin

Always fit new split pins of the correct size for the hole in the bolt or stud. Do not loosen back castle nuts when
fitting a split pin, except in those recommended cases when this forms part of an adjustment.
Always fit new roll pins of an interference fit in the hole.

Circlips, Retaining Rings

Replace any circlips and retaining rings that are removed. Removal weakens and deforms circlips causing
looseness in the circlip groove. When installing circlips and retaining rings, take care to compress or expand
them only enough to install them.
Always use the correct replacement circlip as recommended in the Triumph parts catalogue.

Self-Locking Nuts

Self-locking nuts can be reused, provided resistance can be felt when the locking portion passes over the thread
of the bolt or stud.
DO NOT reuse self-locking nuts in critical locations, e.g. suspension components. Always use the correct
replacement self-locking nut.

Encapsulated Bolts

An encapsulated bolt can be identified by a coloured section of thread which is treated with a locking agent.
Unless a specified repair procedure states otherwise, encapsulated bolts cannot be reused and MUST be
replaced if disturbed or removed.

WARNING

Failure to replace an encapsulated bolt could lead to a dangerous riding condition. Always replace
encapsulated bolts.

Oil and Grease Seals

Replace any oil or grease seals that are removed. Removal will cause damage to an oil seal which, if reused,
would cause an oil leak.
Ensure the surface on which the new seal is to run is free of burrs or scratches. Renew the component if the
original sealing surface cannot be completely restored.
Protect the seal from any surface which could cause damage over which it has to pass when being fitted. Use a
protective sleeve or tape to cover the relevant surface and avoid touching the sealing lip.

Tiger Explorer XR Series

8 of 746

GENERAL INFORMATION

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Öhlins POF5K00 Mounting Instructions preview
POF5K00
Бренд: Öhlins Страницы: 2
Öhlins Mechatronics 35007-01 Installation Instruction preview
Mechatronics 35007-01
Бренд: Öhlins Страницы: 4
Öhlins McPherson Strut MIR 5H02 Mounting Instructions preview
McPherson Strut MIR 5H02
Бренд: Öhlins Страницы: 2
Öhlins KA 590 Mounting Instructions preview
KA 590
Бренд: Öhlins Страницы: 4
Ducati 96480931A Manual preview
96480931A
Бренд: Ducati Страницы: 123
LAZER Lugano User Manual preview
Lugano
Бренд: LAZER Страницы: 19
Kong MOUSE WORK Manual preview
MOUSE WORK
Бренд: Kong Страницы: 72
kellermann Bullet 1000 RB Installation Manual preview
Bullet 1000 RB
Бренд: kellermann Страницы: 2
Ducati SUPERSPORT1000 2003 Owner'S Manual preview
SUPERSPORT1000 2003
Бренд: Ducati Страницы: 328
Romet CRS 125 User Manual preview
CRS 125
Бренд: Romet Страницы: 52
Honda CBR150R Owner'S Manual preview
CBR150R
Бренд: Honda Страницы: 98
hepco & becker 5054560 00 01 Quick Start Manual preview
5054560 00 01
Бренд: hepco & becker Страницы: 4
BMW K1600GTL Rider'S Manual preview
K1600GTL
Бренд: BMW Страницы: 205
VM VM-HF610 Installation Instructions preview
VM-HF610
Бренд: VM Страницы: 2
MT Helmets KRE+ Instructions Manual preview
KRE+
Бренд: MT Helmets Страницы: 116
Beta RR 125 cc Owner'S Manual preview
RR 125 cc
Бренд: Beta Страницы: 248
Beta 2008 URBAN 125cc Service Manual preview
2008 URBAN 125cc
Бренд: Beta Страницы: 370
hepco & becker 710081 Assembly preview
710081
Бренд: hepco & becker Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды