manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Fuel pump connection

5.

Fuel pump plate outlet

6.

Start the motorcycle and allow to run for approximately 20 to 30 seconds. Briefly raise the engine speed
several times to allow any air to be expelled from the system.

18. 

Stop the engine. Remove the radiator cap and check and top up the coolant level as necessary.

19.

Refit the radiator cap.

20.

Disconnect the fuel tank adaptor hose and extension harness.

21.

With the aid of an assistant, lean the motorcycle fully over to the right hand side, and then the left hand side,
to release air trapped in the cooling system.

22. 

Refit the fuel tank (see Fuel Tank - Installation).

23.

Start the motorcycle. Briefly raise the engine speed several times to allow any air to be expelled from the
system.

24. 

Allow the engine to run until the cooling fan operates.

25.

Stop the motorcycle and allow the engine to cool.

26.

WARNING

Do not remove the coolant pressure cap when the engine is hot. When the engine is hot, the coolant inside
the cooling system is hot and also under pressure. Contact with the pressurised coolant will cause scalds
and skin damage.

Check the expansion tank level and top up if necessary (see Coolant Level Adjustment).

27.

Refit the rider’s seat (see Rider’s Seat - Installation).

28.

Water Pump

Note

The oil pump and water pump are supplied as an assembly and cannot be separated. For additional
information, refer to Oil Pump (see Oil Pump - Removal for removal and Oil Pump - Installation for
installation).

Coolant Pressure Cap and Coolant System Testing

WARNING

Do not remove the coolant pressure cap when the engine is hot. When the engine is hot, the coolant inside
the radiator is hot and also under pressure. Contact with hot coolant will cause scalds and skin damage.

Inspection and Testing

Allow the engine temperature to cool for at least 30 minutes.

1.

Remove the coolant pressure cap.

2.

Check the condition of the upper and lower seals of the coolant pressure cap.

3.

1

Tiger Explorer XR Series

358 of 746

COOLING

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

DAELIM S3 Service Manual preview
S3
Бренд: DAELIM Страницы: 20
Baotian BT50QT-9 Service Manual preview
BT50QT-9
Бренд: Baotian Страницы: 30
UNIT 1 FARO User Manual preview
FARO
Бренд: UNIT 1 Страницы: 23
Kabuto FIGO Instruction Manual preview
FIGO
Бренд: Kabuto Страницы: 16
Yamaha FJR1300AS Assembly Manual preview
FJR1300AS
Бренд: Yamaha Страницы: 94
Yamaha FJR1300(S) Supplementary Service Manual preview
FJR1300(S)
Бренд: Yamaha Страницы: 44
hepco & becker 651665 00 22-00-40 Manual preview
651665 00 22-00-40
Бренд: hepco & becker Страницы: 5
Suzuki RV50 Service Manual preview
RV50
Бренд: Suzuki Страницы: 59
WangYe WY50QT-16A Manual preview
WY50QT-16A
Бренд: WangYe Страницы: 19
Paaschburg & Wunderlich HIGHSIDER VICTORY Mounting And Safety Instructions preview
HIGHSIDER VICTORY
Бренд: Paaschburg & Wunderlich Страницы: 5
MOTO GUZZI Stelvio 1200 MY11 2011 Service Station Manual preview
Stelvio 1200 MY11 2011
Бренд: MOTO GUZZI Страницы: 385
Two Brothers Racing 005-3860405-S1 Installation Instructions preview
005-3860405-S1
Бренд: Two Brothers Racing Страницы: 2
Memphis Shades MEB8975 Mounting Instructions preview
MEB8975
Бренд: Memphis Shades Страницы: 2
Yamaha TT-R125Y Owner'S Manual preview
TT-R125Y
Бренд: Yamaha Страницы: 248
Yamaha TT-R50EK 2018 Owner'S Manual preview
TT-R50EK 2018
Бренд: Yamaha Страницы: 86
Suzuki VX800L Manual preview
VX800L
Бренд: Suzuki Страницы: 101
Kinderkraft SAFETY User Manual preview
SAFETY
Бренд: Kinderkraft Страницы: 36
Sealey VS1830.V2 Instructions preview
VS1830.V2
Бренд: Sealey Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды