manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Position the motorcycle on level ground and in an upright position.

1. 

The coolant level within the expansion tank can be inspected on the left hand side of the motorcycle without
removing any covers.

2. 

Check the coolant level in the expansion tank. The coolant level must be between the MAX and MIN level
marks moulded into the expansion tank cover. If the coolant is below the minimum level, the coolant level
must be adjusted.

3. 

3

2

chgw

1

Expansion tank

1.

MAX mark

2.

MIN mark

3.

CAUTION

If the coolant level is found to be low, or if coolant has to be added regularly, inspect the cooling system for
coolant leaks. If necessary, pressure test the system to locate the source of the leak and rectify as
necessary. Loss of coolant may cause the engine to overheat and suffer severe damage.

Coolant Level Adjustment

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

WARNING

Do not remove the coolant pressure cap when the engine is hot. When the engine is hot, the coolant inside
the radiator is hot and also under pressure. Contact with hot coolant will cause scalds and skin damage.

Allow the engine to cool.

1.

The coolant within the expansion tank can be topped up on the left hand side of the motorcycle without
removing any covers.

2. 

Remove the cap from the expansion tank and add coolant mixture through the filler opening until the level
reaches the MAX mark on the expansion tank cover.

3. 

2

Tiger Explorer XR Series

353 of 746

COOLING

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Yamaha YZ450F(V) Owner'S Service Manual preview
YZ450F(V)
Бренд: Yamaha Страницы: 650
Dynojet Power Commander III 718-411 Installation Instructions preview
Power Commander III 718-411
Бренд: Dynojet Страницы: 3
LedGlow Advanced Million Color Mini Motorcycle Lighting Kit Installation Instructions preview
Advanced Million Color Mini Motorcycle Lighting Kit
Бренд: LedGlow Страницы: 3
BMW K 1600 GTL Rider'S Manual preview
K 1600 GTL
Бренд: BMW Страницы: 176
AGV CORSA R Manual preview
CORSA R
Бренд: AGV Страницы: 45
Takegawa 02-01-0284 Instruction Manual preview
02-01-0284
Бренд: Takegawa Страницы: 2
Spartus 901X User Manual preview
901X
Бренд: Spartus Страницы: 24
Cycle Protect The Liberator Installation & Owner'S Manual preview
The Liberator
Бренд: Cycle Protect Страницы: 15
Yamaha XS650SE Shop Manual preview
XS650SE
Бренд: Yamaha Страницы: 215
Yamaha XS1100SH Service Manual preview
XS1100SH
Бренд: Yamaha Страницы: 319
Yamaha TMAX 2020 Service Manual preview
TMAX 2020
Бренд: Yamaha Страницы: 688
Yamaha XMAX YP250R 2013 Owner'S Manual preview
XMAX YP250R 2013
Бренд: Yamaha Страницы: 94
Yamaha KODIAK YFM70KDXM Owner'S Manual preview
KODIAK YFM70KDXM
Бренд: Yamaha Страницы: 180
Yamaha YFM700R Owner'S Manual preview
YFM700R
Бренд: Yamaha Страницы: 156
Yamaha RAPTOR 700R 2022 Owner'S Manual preview
RAPTOR 700R 2022
Бренд: Yamaha Страницы: 160
KTM 60112092010 Information preview
60112092010
Бренд: KTM Страницы: 7
DYNATEK D4K-DCT Manual preview
D4K-DCT
Бренд: DYNATEK Страницы: 1
DYNATEK DDK1-7 Installation Manual preview
DDK1-7
Бренд: DYNATEK Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды