manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

Position a container beneath the rear bevel box oil drain plug.

1. 

1

chew_2

Drain plug

1.

Remove the drain plug and allow all the oil to fully drain out. Discard the sealing washer.

2.

Wipe the drain plug clean, fit a new sealing washer then refit to the final drive and tighten to 

25 Nm

.

3.

Note

The drain plug is magnetic. It is normal for metallic deposits to be attached to the drain plug magnet.

Have an assistant stand the motorcycle upright.

4.

Remove the filler level plug.

5.

Fill with 75W/90 fully synthetic hypoid oil that meets specification API Service Level GL5, such as Castrol
SAF-XO fully synthetic hypoid oil, until the level of oil inside the unit is level with the bottom of the filler.

6. 

Incorporating a new washer, refit the plug and tighten to 

25 Nm

.

7.

Rear Bevel Box - Inspection

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

Remove the rider’s seat (see Rider’s Seat - Removal).
Disconnect the battery, negative (black) lead first.
Support the motorcycle so that the rear wheel is clear of the ground.
Remove the rear wheel (see Rear Wheel - Removal).

WARNING

Do not allow the caliper to hang on the brake hose as this may damage the hose and could lead to loss of
motorcycle control and an accident.

Detach and support the rear brake caliper such that the weight of the caliper is not supported by the brake

1.

Tiger Explorer XR Series

434 of 746

REAR BEVEL BOX / DRIVE SHAFT

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

DAELIM ROADWIN - Brochure preview
ROADWIN -
Бренд: DAELIM Страницы: 2
DMC 25470-00 Installation Instructions preview
25470-00
Бренд: DMC Страницы: 2
GAS GAS EC - 2006 User Manual preview
EC - 2006
Бренд: GAS GAS Страницы: 74
GAS GAS MC Boy 50 User Manual preview
MC Boy 50
Бренд: GAS GAS Страницы: 32
AFX FX-78 Owner'S Manual preview
FX-78
Бренд: AFX Страницы: 52
Evotech ESTR-0317 User Manual preview
ESTR-0317
Бренд: Evotech Страницы: 84
BMW Motorrad R 1150 RT Supplementary User'S Manual preview
R 1150 RT
Бренд: BMW Motorrad Страницы: 28
BMW Motorrad G 310 GS Rider'S Manual preview
G 310 GS
Бренд: BMW Motorrad Страницы: 170
schweisskraft VarioProtect XXL-W TC AIR TH3 Operating Instructions Manual preview
VarioProtect XXL-W TC AIR TH3
Бренд: schweisskraft Страницы: 28
Yamaha YZF-R6 2000 Service Manual preview
YZF-R6 2000
Бренд: Yamaha Страницы: 32
Yamaha YZF250 Owner'S Manual preview
YZF250
Бренд: Yamaha Страницы: 98
Yamaha YZF-R6D Owner'S Manual preview
YZF-R6D
Бренд: Yamaha Страницы: 114
Yamaha YZF-R6P Owner'S Manual preview
YZF-R6P
Бренд: Yamaha Страницы: 128
Yamaha YZF-R7 Owner'S Service Manual preview
YZF-R7
Бренд: Yamaha Страницы: 381
X-TREME xm-700 User Manual preview
xm-700
Бренд: X-TREME Страницы: 6
hepco & becker 8009522 00 01 Manual preview
8009522 00 01
Бренд: hepco & becker Страницы: 2
KTM Power Parts Information preview
Power Parts
Бренд: KTM Страницы: 3
Royal Enfield 350 Clipper Workshop Maintenance Manual preview
350 Clipper
Бренд: Royal Enfield Страницы: 72

Бренды по названию

Популярные бренды

Загрузить еще бренды