Triumph Tiger Explorer XR 2016 Скачать руководство пользователя страница 130 | Manualshive

Страница: 130 / 750

background image

WARNING

The clutch slave cylinder contains no user serviceable parts and replacement piston and dust seals are not
available.
If disassembled, never attempt to reassemble the clutch slave cylinder using the original seals as this could
cause a fluid leak.
The clutch slave cylinder must be replaced If disassembled for any reason.
A dangerous riding condition leading to loss of motorcycle control and an accident could result if this warning
is ignored.

Inspect the clutch slave cylinder carefully for fluid leaks, wear, damage, cracks or deterioration.

1.

Replace the clutch slave cylinder if any of the above are evident.

2.

Clutch Slave Cylinder - Installation

Remove the cable tie or rubber band from the slave cylinder.

1.

Align and fit the union bolt to the clutch hose incorporating new sealing washers. Connect the hose to the
slave cylinder.

2.

Fit the slave cylinder to the clutch cover ensuring that the lifter piece locates correctly in the cylinder. Tighten
the cylinder to clutch cover bolts to

10 Nm

.

3.

Tighten the clutch hose union bolt to

25 Nm

.

4.

Bleed the clutch (see Bleeding the Clutch) and then examine the system for:

5.

Correct clutch operation
Fluid leakage.
Refit the slave cylinder cover. Tighten the new fixings to

4 Nm

.

6.

Clutch - Removal

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

Remove the clutch cover (see Clutch Cover - Removal).

Note

The lifter piece and bearing carrier can be removed by hand.

Remove the lifter piece and bearing carrier.

1.

cjig

2

1

Tiger Explorer XR Series

126 of 746

CLUTCH

«
...
128
129
130
131
132
...
»

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Бренд: Yamaha Страницы: 102

Бренд: hepco & becker Страницы: 6

Бренд: R&G Страницы: 13

Бренд: hepco & becker Страницы: 4

MD-052-2 Series

Бренд: Acewell Страницы: 2

Бренд: AMERICAN IRONHORSE Страницы: 104

V 7 CAFE CLASSIC

Бренд: MOTO GUZZI Страницы: 147

Бренд: Vance and hines Страницы: 5

Бренд: Miller Страницы: 22

Бренд: hepco & becker Страницы: 3

Бренд: Pacific Helmets Страницы: 40

Бренд: Malossi Страницы: 24

Бренд: DYNATEK Страницы: 2

Бренд: Brixton Страницы: 49

Бренд: VESPA Страницы: 80

Бренд: Innovv Страницы: 2

Бренд: Shark Страницы: 8

Ride-On Motorcycle

Бренд: Rovo Kids Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды