manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

CAUTION

Do not allow the wheel to rest on the brake discs, as this may damage the discs. Support the wheel on
wooden blocks, equally spaced around the rim, such that the brake discs are raised above the ground.

Place the wheel on wooden blocks to prevent damage to the brake discs.

2. 

Remove and discard the seals and the bearing circlip.

3.

WARNING

Always wear eye, hand and face protection when using a hammer and drift. Use of a hammer and drift can
cause bearings to fragment. Pieces of fragmented bearing could cause eye and soft tissue injuries if suitable
protective apparel is not worn.

CAUTION

To prevent wheel damage and to aid bearing removal, always apply force evenly on both sides of the bearing
to prevent it from 'tipping' and becoming stuck. Application of uneven force will lead to difficulty in removing
the bearing and to a damaged wheel.

Using a suitable pin punch, through the centre of the wheel, drift out the wheel bearings. Collect the centre
sleeve.

4. 

cdgd

Wheel Bearing Removal

Inspection - Wheels

Front Wheel Bearings - Installation

WARNING

Only remove raised witness marks from within the wheel. Removal of material below any raised areas will
reduce the level of interference between the wheel and the bearings. Loss of interference could cause the
bearing to become loose in the wheel leading to loss of motorcycle control and an accident.

Examine the wheel for any raised witness marks caused by the removal process. Remove any such marks
with fine emery paper or a gentle file.

1. 

Tiger Explorer XR Series

551 of 746

WHEELS / TYRES

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

yasuni R2 Assembly Instructions Manual preview
R2
Бренд: yasuni Страницы: 11
BMW R 1200 C Repair Manual preview
R 1200 C
Бренд: BMW Страницы: 288
Thunderbike 72-72-125 Installation Instructions Manual preview
72-72-125
Бренд: Thunderbike Страницы: 11
Wolfman Monarch Pass M321 Mounting Instructions preview
Monarch Pass M321
Бренд: Wolfman Страницы: 5
Suzuki DR-Z70 Service Manual preview
DR-Z70
Бренд: Suzuki Страницы: 199
Lincoln Electric VIKING 3250D FGS Operator'S Manual preview
VIKING 3250D FGS
Бренд: Lincoln Electric Страницы: 56
TREND AIRPRO MAX User Instructions preview
AIRPRO MAX
Бренд: TREND Страницы: 38
Ducati Multistrada 620 Owner'S Manual preview
Multistrada 620
Бренд: Ducati Страницы: 382
Yamaha WOLVERINE X4 2021 Owner'S Manual preview
WOLVERINE X4 2021
Бренд: Yamaha Страницы: 192
Yamaha WR250F(Y) 2009 Owner'S Service Manual preview
WR250F(Y) 2009
Бренд: Yamaha Страницы: 224
Yamaha WR250FR 2002 Owner'S Service Manual preview
WR250FR 2002
Бренд: Yamaha Страницы: 343
Yamaha WR250F 2022 Owner'S Service Manual preview
WR250F 2022
Бренд: Yamaha Страницы: 404
Yamaha WR250F 2017 Owner'S Service Manual preview
WR250F 2017
Бренд: Yamaha Страницы: 432
Yamaha WR250FM 2021 Owner'S Service Manual preview
WR250FM 2021
Бренд: Yamaha Страницы: 404
Yamaha WR250F(P) Owner'S Service Manual preview
WR250F(P)
Бренд: Yamaha Страницы: 694
Yamaha WR250F(S) Owner'S Service Manual preview
WR250F(S)
Бренд: Yamaha Страницы: 864
Yamaha WR250F(W) Owner'S Service Manual preview
WR250F(W)
Бренд: Yamaha Страницы: 912
Yamaha WR250F(T) Owner'S Service Manual preview
WR250F(T)
Бренд: Yamaha Страницы: 864

Бренды по названию

Популярные бренды

Загрузить еще бренды