manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

CAUTION

engine to overheat and suffer severe damage.

Check the radiator hoses for cracks or deterioration, and hose clamps for tightness in accordance with
scheduled maintenance requirements.

Radiator and Cooling Fan Inspection

Radiator

CAUTION

Using high pressure water, such as from a pressure-washer, can damage the radiator fins and impair the
radiator's efficiency.
Do not obstruct or deflect airflow through the radiator by installing unauthorised accessories in front of the
radiator or behind the cooling fan. Interference with the radiator airflow can lead to overheating and
consequent engine damage.

Check the radiator for stone damage.

1.

Check the radiator core for damage to fins or obstructions to air flow.

2.

Clean off any obstructions with a stream of low-pressure water.

3.

CAUTION

To avoid overheating and consequent engine damage, replace the radiator if the cores are blocked or if the
fins are badly deformed or broken.

Rectify any damage.

4.

Cooling Fan

WARNING

The cooling fan is turned on or off by the chassis ECM, in response to a request sent by the engine ECM.
The request from the engine ECM to turn the cooling fan on or off, is sent to the chassis ECM in response to
a signal received from the coolant temperature sensor.
To prevent injury, never place loose clothing, fingers or hands near the cooling fan, until the engine is
stopped. Loose clothing, fingers or the hands could become trapped during cooling fan operation and cause
crushing injury to the fingers, hands or other parts of the anatomy.

The motorcycle is fitted with a thermostatically controlled electric fan situated behind the radiator. When the fan
operates with the motorcycle stationary or at slow speed, cool air is drawn through the radiator from the front of
the motorcycle.

Check that the cooling fan spins freely and without tight spots.

1.

Check the cooling fan blades for signs of heat distortion.

2.

Rectify as necessary.

3.

Coolant Level Inspection

WARNING

Do not remove the coolant pressure cap when the engine is hot. When the engine is hot, the coolant inside
the radiator is hot and also under pressure. Contact with hot coolant will cause scalds and skin damage.

Tiger Explorer XR Series

352 of 746

COOLING

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Dakota Digital 2000 Series Parts List preview
2000 Series
Бренд: Dakota Digital Страницы: 38
hepco & becker 6609516 01 01 Quick Start Manual preview
6609516 01 01
Бренд: hepco & becker Страницы: 4
Suzuki 990D0-44G00-ALM Fitting Instructions Manual preview
990D0-44G00-ALM
Бренд: Suzuki Страницы: 24
Yoshimura 070BG125511 Manual preview
070BG125511
Бренд: Yoshimura Страницы: 4
DYNATEK D3K7-4 Installation Instructions preview
D3K7-4
Бренд: DYNATEK Страницы: 4
CyClone 866F Owner'S Manual preview
866F
Бренд: CyClone Страницы: 24
Brixton BX 125 2018 User Manual preview
BX 125 2018
Бренд: Brixton Страницы: 49
HYOSUNG RX 125 - Parts Catalog preview
RX 125 -
Бренд: HYOSUNG Страницы: 101
Honda CRF230F 2004 Owner'S Manual preview
CRF230F 2004
Бренд: Honda Страницы: 189
Honda CRF230F 2005 Owner'S Manual preview
CRF230F 2005
Бренд: Honda Страницы: 189
KTM 45412955044S Fitting Instructions Manual preview
45412955044S
Бренд: KTM Страницы: 122
Royal Enfield CO Workshop Maintenance Manual preview
CO
Бренд: Royal Enfield Страницы: 52
Power Riders INDIAN CHIEF User Manual preview
INDIAN CHIEF
Бренд: Power Riders Страницы: 5
HealTech Electronics FI Cleaner Tool User Manual preview
FI Cleaner Tool
Бренд: HealTech Electronics Страницы: 2
Honda CRF250X 2006 Owner'S Manual & Competition Handbook preview
CRF250X 2006
Бренд: Honda Страницы: 180
R&G SS0054 Fitting Instructions Manual preview
SS0054
Бренд: R&G Страницы: 10
Yerf-Dog 31700 Owner'S Manual preview
31700
Бренд: Yerf-Dog Страницы: 16
Safer 90942 Instruction Manual preview
90942
Бренд: Safer Страницы: 33

Бренды по названию

Популярные бренды

Загрузить еще бренды