manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Crankshaft - Installation

Remove the engine from the frame (see Engine - Removal).
Separate the two halves of the crankcase (see Crankcases - Disassembly).
Remove the connecting rods (see Connecting Rods - Removal).
Remove the camshaft drive chain (see Camshaft Drive Chain, Tensioner Blade and Rubbing Strip -
Removal).
Release and remove the crankshaft from the upper crankcase.

1. 

Note

Identify the location of each bearing shell.
Remove all bearings and inspect for damage, wear, overheating (blueing) and any other signs of
deterioration. Replace the bearings as a set if necessary.

Collect the piston cooling jets from the crankcase oil ways beneath the crankshaft bearings.

2.

cdjk

1

Piston cooling jet (one of three)

1.

CAUTION

During crankcase assembly, ensure all three piston cooling jets are re-installed. If the jets are omitted, oil
pressure will be reduced. Running the engine with low oil pressure will cause severe engine damage.

Remove the balancer (see Balancer - Removal).

3.

Crankshaft Main Bearing/Journal Wear

Pistons - Disassembly

CAUTION

Always check the bearing journal clearance (see Crankshaft Main Bearing/Journal Wear), before final
assembly of the crankshaft. Failure to correctly select crankshaft bearings will result in severe engine
damage.

If removed, insert the three piston cooling jets into the main bearing housings in the upper crankcase.

1.

Select and fit new main and big end shell bearings using the selection processes detailed in Connecting Rod
Bearing Selection/ Crankshaft Journal Wear Check and Crankshaft Main Bearing/Journal Wear.

2. 

Tiger Explorer XR Series

153 of 746

CRANKSHAFT / RODS / PISTONS

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

hepco & becker Easyrack 6617501 01 01 Manual preview
Easyrack 6617501 01 01
Бренд: hepco & becker Страницы: 4
HERO Splendor Pro CLASSIC Manual preview
Splendor Pro CLASSIC
Бренд: HERO Страницы: 56
DYNATEK DFCH-2 User Manual preview
DFCH-2
Бренд: DYNATEK Страницы: 4
hepco & becker 6002524 00 01 Assembling Instructions preview
6002524 00 01
Бренд: hepco & becker Страницы: 9
Yamaha FSI-E Owners Workshop Manual preview
FSI-E
Бренд: Yamaha Страницы: 93
Yamaha FJR13AX Owner'S Manual preview
FJR13AX
Бренд: Yamaha Страницы: 114
Yamaha FJR1300AW Owner'S Manual preview
FJR1300AW
Бренд: Yamaha Страницы: 100
Yamaha FJR1300AT Owner'S Manual preview
FJR1300AT
Бренд: Yamaha Страницы: 100
Yamaha FJR1300ASW Owner'S Manual preview
FJR1300ASW
Бренд: Yamaha Страницы: 102
Yamaha Fiore Owner'S Manual preview
Fiore
Бренд: Yamaha Страницы: 74
Yamaha FJR1300APX Owner'S Manual preview
FJR1300APX
Бренд: Yamaha Страницы: 102
Yamaha FJR1300AS(X) Owner'S Manual preview
FJR1300AS(X)
Бренд: Yamaha Страницы: 104
Yamaha FINO AF115F Owner'S Manual preview
FINO AF115F
Бренд: Yamaha Страницы: 80
Yamaha FJR1300AP Supplementary Manual preview
FJR1300AP
Бренд: Yamaha Страницы: 108
Yamaha FJR1300(S) Owner'S Manual preview
FJR1300(S)
Бренд: Yamaha Страницы: 99
Yamaha FJR1300AS Owner'S Manual preview
FJR1300AS
Бренд: Yamaha Страницы: 126
Yamaha FJR Owner'S Manual preview
FJR
Бренд: Yamaha Страницы: 100
Yamaha FJR1300AE Owner'S Manual preview
FJR1300AE
Бренд: Yamaha Страницы: 132

Бренды по названию

Популярные бренды

Загрузить еще бренды