manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

chhp

Pump Body Clearance

For specifications refer toLubrication.

7. 

Measure the pump end clearance.

8.

If any clearance measured is outside the service limits, renew the complete pump.

9.

For specifications refer toLubrication.

10.

If all clearances are within service limits, liberally apply clean engine oil to all internal components. Refit the
oil pump rotor housing to the oil pump body and secure with new fixings. Tighten the fixings to 

10 Nm

.

11. 

Inspect the sprocket and chain for wear and/or damage. Replace the sprocket and chain if wear and/or
damage is found.

12. 

Refit the spacer washer and oil pump sprocket and secure with a new fixing. Using T3880603 - Oil Pump
Restraint to prevent rotation, tighten the fixing to 

12 Nm

.

13. 

Oil Pump - Installation

Heat Exchanger - Removal

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

CAUTION

Before fitting the oil pump to the crankcase ensure the pump internal surfaces have been 'wetted' with clean
engine oil. The pump may fail to pick-up oil from the sump if the surfaces have not been 'wetted'. This will
cause the engine to run without engine oil pressure and will lead to severe engine damage.

Install new O-rings to the coolant inlet and outlet tubes.

1.

1

chhq

Coolant tubes

1.

Fill the oil pump with new engine oil, turning the pump rotor as the oil is poured in to ensure all surfaces are
coated with oil.

2. 

Position the oil pump to the crankcase and push the openings in the water pump over the coolant inlet and
outlet tubes.

3. 

Align the oil pump to the crankcase, and ensure the oil pump dowel correctly locates over the bolt hole.

4.

Tiger Explorer XR Series

213 of 746

LUBRICATION

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Kabuto HIKE Instruction Manual preview
HIKE
Бренд: Kabuto Страницы: 40
Yamaha Star XV250ZC Owner'S Manual preview
Star XV250ZC
Бренд: Yamaha Страницы: 96
R&G BRG0004BK Fitting Instructions Manual preview
BRG0004BK
Бренд: R&G Страницы: 12
Christopeit Sport MB2 9840A Assembly And Exercise Instructions preview
MB2 9840A
Бренд: Christopeit Sport Страницы: 16
Suzuki 2001 GSX1300RK1 HAYABUSA Supplementary Service Manual preview
2001 GSX1300RK1 HAYABUSA
Бренд: Suzuki Страницы: 31
Takegawa 02-01-0284 Instruction Manual preview
02-01-0284
Бренд: Takegawa Страницы: 2
Thunderbike Old style Manual preview
Old style
Бренд: Thunderbike Страницы: 7
DYNATEK DDK1-8 Installation Manual preview
DDK1-8
Бренд: DYNATEK Страницы: 12
Yamaha TW200C Owner'S Manual preview
TW200C
Бренд: Yamaha Страницы: 109
Yamaha TW200 Owner'S Manual preview
TW200
Бренд: Yamaha Страницы: 106
Yamaha TT500C 1976 Owner'S Manual preview
TT500C 1976
Бренд: Yamaha Страницы: 82
Yamaha TT-R50EB Owner'S Manual preview
TT-R50EB
Бренд: Yamaha Страницы: 76
Yamaha TT-R230Y Owner'S Manual preview
TT-R230Y
Бренд: Yamaha Страницы: 74
Yamaha TTR250M Owner'S Manual preview
TTR250M
Бренд: Yamaha Страницы: 93
Yamaha TT250RZ Owner'S Manual preview
TT250RZ
Бренд: Yamaha Страницы: 88
Yamaha TT250RX 2007 Owner'S Manual preview
TT250RX 2007
Бренд: Yamaha Страницы: 86
Yamaha TT-R230X 2007 Owner'S Manual preview
TT-R230X 2007
Бренд: Yamaha Страницы: 79
Yamaha TT-R90 Owner'S Manual preview
TT-R90
Бренд: Yamaha Страницы: 82

Бренды по названию

Популярные бренды

Загрузить еще бренды