manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Front Fork - Inspection

Front Fork - Assembly

Headstock Bearing Check/Adjustment

Headstock Bearing - Removal

Inspect the inner tube for stone chips, scoring, scratches, excessive wear and any other damage. Renew as
necessary.

1. 

Note

Small inclusions in the inner tube may be removed using a fine grade stone or similar.

Inspect the spring for damage, cracks and deformation. Renew the spring if necessary.

2. 

Inspect the bushes for damage. Renew if necessary.

3.

Always renew the oil seal, washer, circlip and dust cap every time the fork is dismantled. Once removed,
these components must not be reused.

4. 

If the damping cylinder has been removed, always renew the damper bolt washer upon reassembly.

5.

WARNING

The front forks comprise many precision machined parts. Total cleanliness must be observed at all times and
assembly must take place in a dirt/dust-free environment.
Dirt ingress may cause damage to the fork parts, leading to incorrect operation, instability, loss of motorcycle
control or an accident.

WARNING

The damping cylinder in the left hand fork is for compression damping while the damping cylinder in the right
hand fork is for rebound damping. Should these damping components get fitted to the wrong fork, the front
suspension will not function correctly and may lead to loss of motorcycle control and an accident.

Note

If removed, ensure the correct damper is fitted to its correct front fork assembly.
The compression damper tube has four holes in its casing.
The rebound damper tube does not have the additional holes.
If the damping cylinder has not been removed, omit steps 1 and 2.

cira

3

1

2

Compression damper - left hand fork

1.

Tiger Explorer XR Series

383 of 746

FRONT SUSPENSION

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

HYOSUNG GD250 Owner'S Manual preview
GD250
Бренд: HYOSUNG Страницы: 98
kellermann BL 1000 PL Installation Instructions preview
BL 1000 PL
Бренд: kellermann Страницы: 2
BMW Motorrad HP2 Megamoto Rider'S Manual preview
HP2 Megamoto
Бренд: BMW Motorrad Страницы: 146
Honda VFR750F 1995 Owner'S Manual preview
VFR750F 1995
Бренд: Honda Страницы: 130
SpeedAngle GMOS JI100S User Manual preview
GMOS JI100S
Бренд: SpeedAngle Страницы: 37
hepco & becker 6264538 00 01 Mounting Instructions preview
6264538 00 01
Бренд: hepco & becker Страницы: 3
Fast H-NAPE CHINSTRAP Operator'S Manual preview
H-NAPE CHINSTRAP
Бренд: Fast Страницы: 24
Triumph ACCESORIES 2005 Price List preview
ACCESORIES 2005
Бренд: Triumph Страницы: 6
Triumph Clothing Range 2006 Catalog preview
Clothing Range 2006
Бренд: Triumph Страницы: 19
Triumph 2007 ROCKET III Overview preview
2007 ROCKET III
Бренд: Triumph Страницы: 20
Triumph Speed Triple Handbook preview
Speed Triple
Бренд: Triumph Страницы: 136
Triumph Speed Triple 1200 RS Owner'S Handbook Manual preview
Speed Triple 1200 RS
Бренд: Triumph Страницы: 184
Triumph Scrambler 1200 XC Service Manual preview
Scrambler 1200 XC
Бренд: Triumph Страницы: 640
KTM Power Parts 60312929000 Information preview
60312929000
Бренд: KTM Power Parts Страницы: 22
KTM Power Parts 3.211.256 Manual preview
3.211.256
Бренд: KTM Power Parts Страницы: 12
KTM 64112922000 Information preview
64112922000
Бренд: KTM Страницы: 7
KTM 125 DUKE EU Setup Instructions preview
125 DUKE EU
Бренд: KTM Страницы: 16
KTM 125 EXC EU 2014 Setup Instructions preview
125 EXC EU 2014
Бренд: KTM Страницы: 27

Бренды по названию

Популярные бренды

Загрузить еще бренды