manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Clip

1.

Clevis pin

2.

Brake hose

3.

Sealing washers

4.

Fixings

5.

Master cylinder

6.

Reservoir bracket

7.

Disconnect the reservoir hose from the master cylinder.

7.

Rear Master Cylinder - Inspection

Remove the boot from the cylinder and pushrod.

1.

Remove the circlip retaining the pushrod to the cylinder. Discard the circlip.

2.

Remove the pushrod and piston set from the master cylinder bore, noting the relative position of the seals
and piston components.

3. 

Rear Master Cylinder - Assembly

Visually inspect the master cylinder bore for wear, scratches or corrosion. Replace as necessary.

1.

Check the piston and cylinder bore for damage, wear or deterioration. Replace as necessary.

2.

Always renew the piston and seal set if the cylinder is dismantled.

3.

Examine the pushrod for bends and damage. Replace as necessary.

4.

Rear Master Cylinder - Installation

WARNING

Never use mineral-based grease (such as lithium or copper based grease) in any area where contact with
the braking system hydraulic seals and dust seals is possible. Mineral-based grease will damage the
hydraulic seals and dust seals in the calipers and master cylinders.
Damage caused by contact with mineral-based grease may reduce braking efficiency resulting in loss of
motorcycle control and an accident.

WARNING

Before installation, all internal brake components should be cleaned and lubricated with clean new DOT 4
brake fluid.
Never use solvents, petrol (gasoline), engine oil, or any other petroleum distillate on internal brake
components as this will cause deterioration of the hydraulic seals in the calipers and master cylinders.
A dangerous riding condition leading to loss of motorcycle control and an accident could result if this warning
is ignored.

Clean the master cylinder bore, piston and seals, with new brake fluid.

1.

Ensure all ports are clear of obstruction.

2.

WARNING

Ensure that the piston and piston seal are fitted facing the same way as noted during removal. A dangerous
riding condition leading to an accident could result from incorrect assembly of the master cylinder.

Install the spring and piston set together.

3.

Tiger Explorer XR Series

491 of 746

BRAKES

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

3M 600 Series User Instructions preview
600 Series
Бренд: 3M Страницы: 26
Honda 1980 CB900C Shop Manual preview
1980 CB900C
Бренд: Honda Страницы: 393
Dynojet 1139.005 Quick Start Manual preview
1139.005
Бренд: Dynojet Страницы: 2
KDX KXD708E Original Instructions Manual preview
KXD708E
Бренд: KDX Страницы: 7
R&G CP0522 Fitting Instructions Manual preview
CP0522
Бренд: R&G Страницы: 15
Suzuki LT-A400FK3 Setup Manual preview
LT-A400FK3
Бренд: Suzuki Страницы: 42
hepco & becker Easyrack 661658 01 01 Manual preview
Easyrack 661658 01 01
Бренд: hepco & becker Страницы: 4
hepco & becker 6304554 00 01 Quick Start Manual preview
6304554 00 01
Бренд: hepco & becker Страницы: 4
Shark Explore-R Manual preview
Explore-R
Бренд: Shark Страницы: 18
National Cycle Quantum N50004 Installation Instructions preview
Quantum N50004
Бренд: National Cycle Страницы: 3
Dynafit BEAST-MIPS User Instructions preview
BEAST-MIPS
Бренд: Dynafit Страницы: 52
MARLINK SmallTrack Assembly Instructions preview
SmallTrack
Бренд: MARLINK Страницы: 3
Sealey MCRS1 Instructions preview
MCRS1
Бренд: Sealey Страницы: 2
Tusk X-Small Dry Duffel Bag Instructions preview
X-Small Dry Duffel Bag
Бренд: Tusk Страницы: 3
Piaa 1100p Series Installation Instructions Manual preview
1100p Series
Бренд: Piaa Страницы: 17
HYOSUNG TE450 - Service Manual preview
TE450 -
Бренд: HYOSUNG Страницы: 262
APRILIA LEONARDO 125 Manual preview
LEONARDO 125
Бренд: APRILIA Страницы: 264
hepco & becker 661754101 01 Manual preview
661754101 01
Бренд: hepco & becker Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды