manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

WARNING

motorcycle control and an accident.

WARNING

Before installation, all internal brake components should be cleaned and lubricated with clean new DOT 4
brake and clutch fluid.
Never use solvents, petrol (gasoline), engine oil, or any other petroleum distillate on internal brake
components as this will cause deterioration of the hydraulic seals in the calipers and master cylinders.
A dangerous riding condition leading to loss of motorcycle control and an accident could result if this warning
is ignored.

Lubricate the piston and cylinder with new, clean brake and clutch fluid.

1. 

WARNING

Ensure that the piston and piston seal are fitted facing the same way as noted during removal. A dangerous
riding condition leading to an accident could result from incorrect assembly of the master cylinder.

Fit the new piston set into the master cylinder and retain with a new circlip.

2.

Refit the master cylinder boot.

3.

Front Brake Master Cylinder - Installation

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

Locate the master cylinder to the handlebars and position the clamp with the 'UP' arrow pointing upwards.

1.

1

chkz

2

'UP' Arrow

1.

Alignment mark

2.

Align the master cylinder/clamp split line with the alignment mark on the handlebar.

2.

Tighten the clamp bolts, upper first and then the lower to 

12 Nm

.

3.

Connect the brake hose to the master cylinder incorporating new sealing washers. Tighten the banjo bolt to

4.

Tiger Explorer XR Series

477 of 746

BRAKES

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

GAS GAS PAMPERA 400 - 2006 User Manual preview
PAMPERA 400 - 2006
Бренд: GAS GAS Страницы: 70
Honda st1300/a 2007 Setup Instructions preview
st1300/a 2007
Бренд: Honda Страницы: 28
Regal Raptor DAYTONA 125 User Manual preview
DAYTONA 125
Бренд: Regal Raptor Страницы: 48
Cobra CX50FWE Manual preview
CX50FWE
Бренд: Cobra Страницы: 80
National Cycle Quantum hardcoated N30214-WK Assembly Instructions And Owner'S Manual preview
Quantum hardcoated N30214-WK
Бренд: National Cycle Страницы: 13
NEO TOOLS 97-590 Instruction Manual preview
97-590
Бренд: NEO TOOLS Страницы: 8
Corbin CA-BAG-ST Manual preview
CA-BAG-ST
Бренд: Corbin Страницы: 4
hepco & becker 654997 01 02 Quick Start Manual preview
654997 01 02
Бренд: hepco & becker Страницы: 2
Vance and hines 48421 Installation Instructions preview
48421
Бренд: Vance and hines Страницы: 5
hepco & becker 5054560 00 01 Quick Start Manual preview
5054560 00 01
Бренд: hepco & becker Страницы: 4
hepco & becker 6264538 00 01 Mounting Instructions preview
6264538 00 01
Бренд: hepco & becker Страницы: 3
Fast H-NAPE CHINSTRAP Operator'S Manual preview
H-NAPE CHINSTRAP
Бренд: Fast Страницы: 24
Derbi GPR 125 4T Owner'S Handbook Manual preview
GPR 125 4T
Бренд: Derbi Страницы: 179
Rockford Fosgate Element Ready TMS69BL14 Installation & Operation Manual preview
Element Ready TMS69BL14
Бренд: Rockford Fosgate Страницы: 8
No-Mar CYCLE HILL HD PLUS Assembly Instructions preview
CYCLE HILL HD PLUS
Бренд: No-Mar Страницы: 4
N-Com ESS III Quick Manual preview
ESS III
Бренд: N-Com Страницы: 28
Kemimoto B0117-00101BK Installation Tips preview
B0117-00101BK
Бренд: Kemimoto Страницы: 3
Xenith X2E Player'S Manual preview
X2E
Бренд: Xenith Страницы: 5

Бренды по названию

Популярные бренды

Загрузить еще бренды