Triumph Tiger Explorer XR 2016 Скачать руководство пользователя страница 105 | Manualshive

Страница: 105 / 750

background image

WARNING

Before starting work, ensure the motorcycle is stabilised and adequately supported. This will help prevent it
from falling and causing injury to the operator or damage to the motorcycle.

Remove the camshafts (see Camshafts - Removal).
Remove the tensioner blade pin and remove the tensioner blade through the right hand crankshaft cover
opening in the crankcase.

1.

Remove the rubbing strip pin and allow the rubbing strip to drop. This will allow the camshaft drive chain to
be unhooked from the crankshaft sprocket.

2.

Unhook the camshaft drive chain from the crankshaft sprocket and remove it through the right hand
crankshaft cover opening in the crankcase.

3.

Remove the rubbing strip through the right hand crankshaft cover opening in the crankcase.

4.

Camshaft Chain - Inspection

Visual in situ checks can also be made as follows:

Check for significant blue discolouration of the drive chain plates indicating excessive heat build-up.

1.

Examine all of the pins for signs of rotation.

2.

Check for cracking or deep scratching of the drive chain plates.

3.

Check for severe wear of the inner plates as indicated in the diagram below.

4.

ccrv

For a more thorough check, proceed as follows:

Remove the drive chain from the engine.

1.

Suspend the drive chain from a pin or hook with a 13 kg weight attached at the lower end.

2.

cajs

Tiger Explorer XR Series

101 of 746

CYLINDER HEAD

«
...
103
104
105
106
107
...
»

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Бренд: R&G Страницы: 13

Бренд: X-lite Страницы: 84

Бренд: Vance and hines Страницы: 5

Бренд: GPX Страницы: 44

Бренд: Bagster Страницы: 2

Бренд: RIEJU Страницы: 152

Бренд: Petzl Страницы: 4

Бренд: RADE/GARAGE Страницы: 6

Бренд: APRILIA Страницы: 256

Бренд: KTM Страницы: 7

Slingshot R 2020

Бренд: Polaris Страницы: 173

Бренд: Royal Enfield Страницы: 104

Бренд: Ossa Страницы: 344

Бренд: Yamaha Страницы: 77

Бренд: Nolan Страницы: 52

Pulsar 180 CC DTS-i

Бренд: Bajaj Страницы: 16

Бренд: LAZER Страницы: 6

Бренд: BGS technic Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды