manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

brake application is related to the level of braking force applied by the rider through the front brake lever. Use of
the rear brake pedal alone will only apply the rear brake.
The front and rear brake hydraulic circuits are separate and are not connected in any way inside the modulator.
The ABS ECM continuously calculates the front and rear wheel speeds, and from these inputs the ABS ECM
calculates the estimated motorcycle speed, wheel deceleration/acceleration, the wheel speed difference and the
wheel slip (skid) rate. This is calculated by comparing the calculated wheel speeds with the calculated vehicle
speed, so that if one wheel speed deviates significantly from the other two readings, this wheel is determined to
be skidding.
Under braking, if the ABS ECM detects that either wheel is about to slip, due to the brake force exceeding the
available traction between the tyre and road surface (the wheel will begin to slip or 'skid'), the ABS ECM very
rapidly releases and re-applies the brake pressure to prevent the wheel from skidding.
This is felt through the brake pedal or lever as a rapid 'pulsing'.
The ABS ECM also continuously monitors the motorcycle lean angle measurements provided by the IMU. If the
motorcycle is leaning in a corner and ABS is activated, the ABS ECM uses the lean angle measurements to
continually adapt the level of ABS intervention in a manner most suitable to help the rider maintain motorcycle
control.
If the rider reduces braking effort, or traction increases (so that traction exceeds braking force, the wheel will
rotate once more) the wheel will no longer lock up. The ABS system will detect this and stop controlling brake
pressure, and return to its monitoring state.
The system has a self diagnostic function built-in which monitors the fail safe relay, solenoid valves, motor relay,
wheel speed sensors, power supply and ground, as well as internal ABS ECM functions. In the event of a
malfunction being detected, the ABS ECM will illuminate the ABS warning light, and store a diagnostic trouble
code in the system memory. This stored data can then be recovered using a special service tool which is
mandatory for all Triumph dealers. In this way, precise diagnosis of a fault can be made and the fault quickly
rectified.
Under normal operation, the ABS warning light will flash on and off after ignition on until the vehicle speed
exceeds 3mph (5 km/h). If a trouble code is stored the ABS warning light will stay illuminated and the ABS will
not function, however the brakes will continue to operate as a non-ABS braking system. If the ABS warning light
does not extinguish, or illuminates whilst the motorcycle is being ridden, refer to the ABS system diagnostics
(see System Diagnostics).

ABS - Component Location

Tiger Explorer XR Series

508 of 746

BRAKES

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

LAZER Century User Manual preview
Century
Бренд: LAZER Страницы: 6
ICON VARIANT Instruction Manual preview
VARIANT
Бренд: ICON Страницы: 8
Öhlins SD 053 Mounting Instructions preview
SD 053
Бренд: Öhlins Страницы: 8
X-lite X-903 Ultra Carbon 29 Safety And Instructions For Use preview
X-903 Ultra Carbon 29
Бренд: X-lite Страницы: 116
KTM 450 SX-F 2019 Owner'S Manual preview
450 SX-F 2019
Бренд: KTM Страницы: 163
SUOMY C1SF0001 Instructions For User preview
C1SF0001
Бренд: SUOMY Страницы: 84
Suzuki 990D0-44G00-ALM Fitting Instructions Manual preview
990D0-44G00-ALM
Бренд: Suzuki Страницы: 24
Big Dog 2006 Chopper Owner'S Manual preview
2006 Chopper
Бренд: Big Dog Страницы: 100
Touratech 01-040-2017-0 Instruction preview
01-040-2017-0
Бренд: Touratech Страницы: 4
KTM 690 SMC R 2016 Series Setup Instructions preview
690 SMC R 2016 Series
Бренд: KTM Страницы: 18
Pro Moto Billet Fastway PMB-01-5203 Quick Manual preview
Fastway PMB-01-5203
Бренд: Pro Moto Billet Страницы: 2
APRILIA 8140172 Service And Repair Manual preview
8140172
Бренд: APRILIA Страницы: 279
Cagiva V RAPTOR 1000 Specifications - Operation - Maintenance preview
V RAPTOR 1000
Бренд: Cagiva Страницы: 142
APRILIA RST FUTURA - 2001 Service Manual preview
RST FUTURA - 2001
Бренд: APRILIA Страницы: 358
KTM 2015 450 SC-F USA Owner'S Manual preview
2015 450 SC-F USA
Бренд: KTM Страницы: 105
Rothewald 10010259 Instructions For Use Manual preview
10010259
Бренд: Rothewald Страницы: 27
3M L-905 Reassembly preview
L-905
Бренд: 3M Страницы: 6
DAELIM DAYSTAR FI Owner'S Manual preview
DAYSTAR FI
Бренд: DAELIM Страницы: 68

Бренды по названию

Популярные бренды

Загрузить еще бренды