manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

1

2

chlf

Scrivets

1.

Infill panel

2.

Refit the airbox (see Airbox - Installation).
Refit the fuel tank (see Fuel Tank - Installation).
Reconnect the battery, positive (red) lead first.

WARNING

Use only DOT 4 specification brake fluid as listed in the General Information section of this manual. The use
of brake fluids other than those DOT 4 fluids listed in the General Information section may reduce the
efficiency of the braking system leading to an accident.
Observe the brake fluid handling warnings given earlier in this section of the manual.

Fill and bleed the front brakes (see Bleeding the Front Brakes, Renewing Brake Fluid).
Fill and bleed the rear brakes (see Bleeding the Rear Brakes, Renewing Brake Fluid).
Refit the rider’s seat (see Rider’s Seat - Installation).
Check for correct brake operation. Rectify as necessary.

WARNING

It is dangerous to operate the motorcycle with defective brakes; you must have your authorised Triumph
dealer take remedial action before you attempt to ride the motorcycle again. Failure to take remedial action
may reduce braking efficiency leading to loss of motorcycle control and an accident.

ABS - System Description

This model is fitted with an electronic, partially integrated, Optimised Cornering Anti-lock Brake System
(OCABS) which is designed to prevent the wheels from locking or skidding by reducing braking effort to the front
or rear brake caliper when wheel-lock is detected.
The system consists of a hydraulic modulator and ABS ECM assembly mounted to a bracket to the right hand
side of the frame near the headstock, a front wheel speed sensor mounted to the front fork, a rear wheel speed
sensor mounted to the rear bevel box and an Inertial Measurement Unit (IMU) mounted beneath the seat bridge.
The front pulser ring is mounted to the left hand brake disc and the rear pulser ring is mounted to the rear bevel
box hub.
The front and rear master cylinders are connected by lines to the modulator and from the modulator the pipes
connect to the brake calipers.
The front and rear brakes are partially integrated electronically by the ABS ECM. When the front brake is
applied, the ABS ECM will also apply a small amount of rear brake for balanced braking. The amount of rear

Tiger Explorer XR Series

507 of 746

BRAKES

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

hepco & becker 6304567 00 01 Quick Start Manual preview
6304567 00 01
Бренд: hepco & becker Страницы: 4
KTM 50 SX 2015 Setup Instructions preview
50 SX 2015
Бренд: KTM Страницы: 13
hepco & becker 650949 01 01 Quick Start Manual preview
650949 01 01
Бренд: hepco & becker Страницы: 2
KTM 950 SUPER ENDURO R 2006 Owner'S Manual preview
950 SUPER ENDURO R 2006
Бренд: KTM Страницы: 86
Corbin CA-BAG-ST Manual preview
CA-BAG-ST
Бренд: Corbin Страницы: 4
Cycle Protect The Liberator Installation & Owner'S Manual preview
The Liberator
Бренд: Cycle Protect Страницы: 15
hepco & becker 6536507 00 01 Mounting Instructions preview
6536507 00 01
Бренд: hepco & becker Страницы: 7
SHERCO XY 125 Owner'S Manual preview
XY 125
Бренд: SHERCO Страницы: 102
Yamaha PW50 2020 Owner'S Manual preview
PW50 2020
Бренд: Yamaha Страницы: 74
Yamaha PW50 2013 Owner'S Manual preview
PW50 2013
Бренд: Yamaha Страницы: 76
Yamaha PW50(Y) Owner'S Manual preview
PW50(Y)
Бренд: Yamaha Страницы: 72
Yamaha Nouvo AT115S Owner'S Manual preview
Nouvo AT115S
Бренд: Yamaha Страницы: 78
Yamaha Neo's 4 YN50F Owner'S Manual preview
Neo's 4 YN50F
Бренд: Yamaha Страницы: 76
Yamaha NMX GPD125-A Owner'S Manual preview
NMX GPD125-A
Бренд: Yamaha Страницы: 90
Yamaha PW50(S) Owner'S Manual preview
PW50(S)
Бренд: Yamaha Страницы: 164
Yamaha PW50(P) Owner'S Manual preview
PW50(P)
Бренд: Yamaha Страницы: 164
Yamaha PW50(N) Owner'S Manual preview
PW50(N)
Бренд: Yamaha Страницы: 164
Yamaha PW50(R) Owner'S Manual preview
PW50(R)
Бренд: Yamaha Страницы: 164

Бренды по названию

Популярные бренды

Загрузить еще бренды