manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Electrical Precautions

The following guidelines are intended to ensure the safety of the operator whilst preventing damage to the
electrical and electronic components fitted to the motorcycle. Where necessary, specific precautions are detailed
in the relevant sections of this manual which should be referred to prior to commencing repair operations.
Equipment - Prior to commencing any test procedure on the motorcycle ensure that the relevant test equipment
is working correctly and any harness or connectors are in good condition, in particular mains leads and plugs.

WARNING

The ignition system produces extremely high voltages. Do not touch any part of the ignition system or any
cables while the engine is running.
An electric shock caused by contact with the ignition system may lead to illness, injury or death.

WARNING

Wearers of surgically implanted heart pacemaker devices should not be in close proximity to ignition circuits
and/or diagnostic equipment.
The ignition system and any diagnostic equipment may interrupt the normal operation of such devices
causing illness or death.

WARNING

The battery contains harmful materials. Always keep children away from the battery whether or not it is fitted
in the motorcycle.
Do not jump start the battery, touch the battery cables together or reverse the polarity of the cables as any of
these actions may cause a spark which would ignite battery gases causing a risk of personal injury.

High Voltage Circuits - Whenever disconnecting live H.T. circuits always use insulated pliers. Exercise caution
when measuring the voltage on the coil terminals while the engine is running. High voltage spikes can occur on
these terminals.
Connectors and Harness - The engine of a motorcycle is a particularly hostile environment for electrical
components and connectors. Always ensure these items are dry and oil-free before disconnecting and
connecting test equipment. Never force connectors apart either by using tools or by pulling on the wiring itself.
Always ensure locking mechanisms are disengaged before removal and note the orientation to enable correct
reconnection. Ensure that any protective covers and substances are replaced if disturbed.
Having confirmed a component to be faulty, switch off the ignition and disconnect the battery negative (black)
lead first. Remove the component and support the disconnected harness. When replacing the component keep
oily hands away from electrical connection areas and push connectors home until any locking mechanism
becomes fully engaged.

Battery Disconnecting

Before disconnecting the battery, switch off all electrical equipment.

WARNING

To prevent the risk of a battery exploding and to prevent damage to electrical components ALWAYS
disconnect the battery negative (black) lead first. When reconnecting the battery, always connect the positive
(red) lead first, then the negative (black) lead. Always disconnect the battery when working on any part of the
electrical system.
Failure to observe the above warnings may lead to electrical damage and a fire hazard which could cause
personal injury.

Always ensure that battery leads are routed correctly and are not close to any potential chafing points.

Tiger Explorer XR Series

13 of 746

GENERAL INFORMATION

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

Kabuto FR-1 Instruction Manual preview
FR-1
Бренд: Kabuto Страницы: 12
Ducati MONSTER 1100 Owner'S Manual preview
MONSTER 1100
Бренд: Ducati Страницы: 128
R&G BRG0013 Fitting Instructions Manual preview
BRG0013
Бренд: R&G Страницы: 9
Evotech ESTR-0317 User Manual preview
ESTR-0317
Бренд: Evotech Страницы: 84
Yoshimura RACE 11621C0520 Manual preview
RACE 11621C0520
Бренд: Yoshimura Страницы: 7
HYOSUNG Aquila GT250 R Ej Service Manual preview
Aquila GT250 R Ej
Бренд: HYOSUNG Страницы: 37
BMW S 1000XR 2018 Rider'S Manual preview
S 1000XR 2018
Бренд: BMW Страницы: 241
Shark RIDILL Owner'S Manual preview
RIDILL
Бренд: Shark Страницы: 92
F4Customs Can-Am Spyder RT Quick Start Manual preview
Can-Am Spyder RT
Бренд: F4Customs Страницы: 3
BGS technic 8858 Manual preview
8858
Бренд: BGS technic Страницы: 11
Baotian BT49QT-18E User Manual preview
BT49QT-18E
Бренд: Baotian Страницы: 22
HYOSUNG RX 125 - Service Manual preview
RX 125 -
Бренд: HYOSUNG Страницы: 175
KTM 600.12.073.044 Mounting Instructions preview
600.12.073.044
Бренд: KTM Страницы: 13
Vinz Fiori Instruction Manual preview
Fiori
Бренд: Vinz Страницы: 23
Scorpa SY 250 Owner'S Manual preview
SY 250
Бренд: Scorpa Страницы: 14
Thunderbike 28-73-040 Manual preview
28-73-040
Бренд: Thunderbike Страницы: 4
Takegawa Hyper S-stage Instruction Manual preview
Hyper S-stage
Бренд: Takegawa Страницы: 10
Yingang YG125-25 Maintenance Manual preview
YG125-25
Бренд: Yingang Страницы: 144

Бренды по названию

Популярные бренды

Загрузить еще бренды