manualshive.com logo in svg

Triumph Tiger Explorer XR 2016, Руководство по обслуживанию


Поделиться
Скачать
background image

Apply a thin smear of grease to each journal and a small quantity of silicone release agent to each bearing.

3. 

Trim a length of the Plastigauge to fit across each journal. Fit the strips to each journal using the grease to
hold the Plastigauge in place.

4. 

Note

Do not turn the crankshaft during crankcase assembly and disassembly as this will cause damage to
the Plastigauge.

Assemble the crankcase halves and tighten the fixings as described in Crankcases - Assembly.

5.

Separate the crankcase halves (see Crankcases - Disassembly).

6.

Using the gauge provided with the Plastigauge kit, measure the width of the compressed Plastigauge.

7.

chdw

Checking Crankshaft Journal Clearance using

Plastigauge

Record the clearance measurements for each crankshaft main bearing/journal.

8.

For specifications refer toCrankshaft.

9.

If the clearance exceeds the service limit, measure the diameter of the crankshaft main journal.

Note

If any journal has worn beyond the service limit, the crankshaft must be replaced. Due to the
techniques used during manufacture, the crankshaft cannot be reground and no oversize bearings
are available.

Select bearings as follows:

Measure and record the diameter of each crankshaft main bearing journal.

1.

Measure and record each main bearing bore diameter in the crankcase (bearings removed).

2.

Main Bearing Selection Chart (all dimensions in mm)

Shell Colour

Crankcase Bore

Journal Diameter

Running Clearance

Red

41.125 to 41.116

37.976 to 37.969

0.046 to 0.020

Blue

41.125 to 41.116

37.968 to 37.960

0.045 to 0.020

Blue

41.134 to 41.126

37.976 to 37.969

0.045 to 0.022

Green

41.134 to 41.126

37.968 to 37.960

0.046 to 0.022

Compare the data found with the chart above to select bearings individually by journal.

Tiger Explorer XR Series

155 of 746

CRANKSHAFT / RODS / PISTONS

Содержание Tiger Explorer XR 2016















































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Tiger Explorer XR 2016

ACERBIS STEEL CARBON User Manual preview
STEEL CARBON
Бренд: ACERBIS Страницы: 72
Ohlins FGR 156 Mounting Instructions preview
FGR 156
Бренд: Ohlins Страницы: 8
AFX FX-78 Owner'S Manual preview
FX-78
Бренд: AFX Страницы: 52
Suzuki 990D0-28K50-CLE Installation Instructions Manual preview
990D0-28K50-CLE
Бренд: Suzuki Страницы: 12
KTM F9903S6 Setup Instructions preview
F9903S6
Бренд: KTM Страницы: 26
Yamaha TMAX ABS Series Owner'S Manual preview
TMAX ABS Series
Бренд: Yamaha Страницы: 122
Yamaha Tenere 700 2024 Owner'S Manual preview
Tenere 700 2024
Бренд: Yamaha Страницы: 110
Yamaha YZFR6X(C) Owner'S Manual preview
YZFR6X(C)
Бренд: Yamaha Страницы: 120
DYNATEK 7-11P Manual preview
7-11P
Бренд: DYNATEK Страницы: 4
EINHELL BG-SH 1 Original Operating Instructions preview
BG-SH 1
Бренд: EINHELL Страницы: 48
hepco & becker 5039515 00 05 Quick Start Manual preview
5039515 00 05
Бренд: hepco & becker Страницы: 3
Fekon 150-14 Owner'S Manual preview
150-14
Бренд: Fekon Страницы: 24
Happy Trails HTP1-8-30 Quick Start Manual preview
HTP1-8-30
Бренд: Happy Trails Страницы: 2
Sealey SMC3 Quick Start Manual preview
SMC3
Бренд: Sealey Страницы: 2
Sealey MS0630 Quick Start Manual preview
MS0630
Бренд: Sealey Страницы: 2
Sealey MS062 Quick Start Manual preview
MS062
Бренд: Sealey Страницы: 2
Sealey mc454 Quick Start Manual preview
mc454
Бренд: Sealey Страницы: 2
Sealey FPS7.V2 Quick Start Manual preview
FPS7.V2
Бренд: Sealey Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды